JVC RX-DV3RSL Front speaker output balance -BAL balance, Tone-BASS and Treble, About auto memory

7Front speaker output balance —“BAL (balance)”

DIGITAL AUTO
L	R	SPK.
		VOLUME

If the sounds you hear from the front right and left speakers are unequal, you can adjust the speaker output balance.

Adjust the output balance appropriately from the listening point within the range of R (Right) –21 to CENTER (0) or CENTER (0) to L (Left) –21.

Note:

•“CENTER” is the initial setting. If you have already changed the setting, another setting will be shown.

7Speaker output levels—“SUBWFR (subwoofer),” “CENTER,” “REAR L (left),” and “REAR R (right)”

DIGITAL AUTO
	L		R	SPK.
				VOLUME
	SUBWFR
DIGITAL AUTO
DIGITAL	L	C	R	SPK.
				VOLUME
	SUBWFR LFE
	LS		RS
DIGITAL AUTO
DIGITAL	L	C	R	SPK.
				VOLUME
	SUBWFR LFE
	LS		RS
DIGITAL AUTO
DIGITAL	L	C	R	SPK.
				VOLUME
	SUBWFR LFE
	LS		RS

7Tone—“BASS” and “TREBLE”

DIGITAL AUTO
L	R	SPK.
		VOLUME
DIGITAL AUTO
L	R	SPK.
		VOLUME

You can adjust the bass and treble sounds as you like.

You can adjust the speaker output levels if you have set the speaker information appropriately.

•You can adjust the output level for center and/or rear speakers only when one of proper Surround modes is activated (see page 31).

Adjust the speaker output level within the range of –10 to +10 in 1 step interval.

Note:

• “0” is the initial setting. If you have already changed the setting,

Adjust the tone within the range of –10 to +10 in 2 steps	another setting will be shown.
intervals.

Note:	7 DAP effect level—“EFFECT”
• “0” is the initial setting. If you have already changed the setting,
another setting will be shown.		ANALOG		DSP
		L	R	SPK.	VOLUME
		SUBWFR
		LS	RS

Adjusting sound from the remote control

1Press SOUND.

Number buttons now work for sound adjustments.

2Adjust the level as follows:

To adjust subwoofer, press SUBWOOFER + or –. To adjust center speaker, press CENTER + or –. To adjust left rear speaker, press REAR•L + or –. To adjust right rear speaker, press REAR•R + or –.

To adjust the effect level (for DAP mode), press EFFECT.

While one of DAP modes is activated (the DSP indicator lights up on the display), you can adjust the effect level.

For details about DAP modes, see pages 29 to 32.

Adjust the effect level within the range of 1 to 5.

Note:

•“3” is the initial setting. If you have already changed the setting, another setting will be shown.

About auto memory		The following can be stored for each source:
This unit memorizes the settings for each source:		•	Analog/digital input mode (see page 13)
		•	Input attenuator mode (see page 14)
•	when you turn off the power (see page 11)
		•	Front speaker output balance (see above or page 54)
•	when you change the source (see page 11)
		•	Speaker output level (see above or page 55)
•	when you change the analog/digital input mode (see page 13)
		•	Tone adjustment (see above or page 54)
•	when you change the source name (see page 14)
		•	DAP effect level (see above)
When you change the source, the memorized settings for the
		•	Surround mode selection (see page 31)
newly selected source are automatically recalled.

Note:

• If the source is FM or AM, you can assign a different setting for each band.

28