JVC RX-DV3RSL manual Operating Other Manufacturers’ Equipment, Changing the Preset Signal Codes

Operating Other Manufacturers’ Equipment

This remote control supplied with the unit can transmit control signals for other manufacturers’ TVs, STBs, and VCRs.

By changing the transmittable signals from preset ones to other manufacturers’, you can operate other manufacturers’ components using this remote control.

Changing the Preset Signal Codes

To operate other manufacturers’ equipment using this remote control

•Aim the remote control directly at the remote sensor on each equipment.

•To operate a source with the remote control, the source must be selected using source selecting buttons on the remote control.

•Refer also to the manuals supplied with your equipment.

7To change the transmittable signals for operating other manufacturers’ TV

1.	Press and hold		STANDBY/ON
	STANDBY/ON TV.	STB	VCR	TV	AUDIO
2.	Press TV.	TV	TAPE	CDR	FM/AM
	TV DIRECT		STB	VCR	DVD
3. Enter the manufacturer’s code			EFFECT	CENTER
	using the number buttons (1–9,		1	2	3
			TEST	REAR·L
	0).		4	5	6
		SURR ON/OFF		REAR·R
	See the right to find the code.
			7	8	9
		SURR MODE – SUBWOOFER +
			10/0	+10
				100+

4. Release STANDBY/ON TV.

You can perform the following operations on the TV:

STANDBY/ON TV	: Turns on or off the TV.
TV VOL + or –	: Adjusts the volume.
TV/VIDEO	: Sets the input mode (either TV or
	VIDEO).

After pressing TV, you can perform the following operations on a TV:

TV/STB CH + or – :Changes the channels.

1 – 9, 0, 100+ : Selects the channels.

For channel number 5, press 5.

For channel number 10, press 1, then 0. For channel number 23, press 2, then 3. For channel number 135, press 100+, 3, then 5.

TV RETURN will function as the ENTER button if your equipment requires pressing ENTER after selecting a channel number.

Notes:

•Refer also to the manual supplied with your TV.

•All the functions listed on the left may not be assigned to the buttons for some TVs.

•If you cannot change the channels of some TVs by pressing the number buttons, press TV/STB CH + or – for changing the channels.

5.Try to operate your TV by pressing

STANDBY/ON TV.

When your TV turns on or off, you have entered the correct code.

If there are more than one code listed for your brand of TV,

try each one until the correct one is entered.

Manufactures’ codes for TV

Manufacturer	Codes
JVC	00*, 02, 13, 14, 47, 74
Akai	01, 02
Blaupunkt	03, 04
Fisher	01, 05
Grundig	03, 06, 07
Hitachi	08 – 10, 49
Iraddio	02
Itt/Nokia	11, 12
Loewe	06, 15, 16
Magnavox	08, 17, 49
Mets	50 – 53
Mitsubishi	08, 18 – 20
Miver	21
Nordmende	22, 23
Okano	15
Panasonic	24 – 27, 76
Philips	15, 17, 28, 75
Quelle	52 – 67
RCA/PROSC	08, 24, 29 – 31, 48
SABA	32, 33, 68 – 70
Samsung	06, 08, 16, 34, 35, 49
Sanyo	01, 05
Schneider	02, 15, 36
Sharp	37, 38, 77
Sony	39
Telefunken	40 – 42, 69
Thomson	71, 72
Toshiba	37, 43, 44
Zenith	45, 46

*“00” is the initial JVC code.

Note:

•Manufacturers’ codes are subject to change without notice. If they are changed, this remote control cannot operate the equipment.

63