Cateye EC-3700, EC-3600 service manual ES-8Replacing the Printer

Page 34

ES-8Replacing the Printer

	Applicable Models:	EC-1600	EC-3700
ES-8	Replacing the Printer	Printer Unit
1. Open the control unit into upper and lower bodies by referring
to the Section ES-6 "Replacing the Panel Keyboard (1) & (2)."			CN-2 Connector
			CN-2 Connector
2. unit is fixed to the lower body with two screws. Remove these
two screws. (Fig. 1)
3. The printer unit can be removed after detaching cable
connectors CN-2 and CN-3 of the printer unit. To remove the
connector CN-3, just pull it, while to remove connector CN-2,
the use of tweezer will be recommended. (Fig. 2)
4. Connect the connector CN-2 of the brandnew printer unit.
Then, connect CN-3. For the connection, press it while moving		Printer Fixing Screws	CN-3 Connector
it to right and left side alternatively.		Printer Fixing Screws
it to right and left side alternatively.

5.	Fix the printer unit with two screws. (Fig. 1)	Fig. 1	Fig. 2
		Fig. 1

6.	Put the upper and lower bodies together, and fix them with
	eight screws.
7.	Adjust the printing darkness by referring to the Section ES-9
	"Adjusting the Printing Darkness."
8.	Mount the control unit to the main unit.

Cateye Ergociser Series 1000 Service Manual

32

Image 34

Contents Cateye Ergociser Index Applicable Models EC-1200 EC-1600 EC-3600 EC-3700ServiceManual Flywheelw/o TypeUpright ForParts OfName Applicable Models EC-1200Name of Parts for Upright Type w/o Flywheel Name of Parts for Upright Type w/ Flywheel EC-1600OfPartsforUpright FlywheelTypew NameName of Parts for Recumbent Type EC-3600 EC-3700OFF Name of Parts for Belt Drive Type ADDEC-3600B/EC-3700B EC-3600B/EC-3700BCircuit Diagram Circuit Diagram for Automatic Type Cateye Ergociser1No Display on Control Unit after Power on No Display on Control Unit after Power onEC-1200 EC-1600 EC-3600 EC-3700 Main unit in accordance with the following procedures Check Method of Causes Repair Method Explanation Figures2No Display of Cadence No Display of Pulse Rate No Printer Operation Printer is not used. Check if the No.4 select switch onDefective ES-3 Replacing the Power Supply Board EC-1600 EC-3700No Loading Check of mechanical systems Check Method of Causes Repair Method5No Loading Check of Electrical Systems Remove the connector CN-1 from the power supply boardNo Loading Check of Electrical Systems Section ES-2 Replacing the 5P Cable6No Pedal Rotation Locked No Pedal Rotation LockedEC-1600 EC-3600 EC-3700 1Unusual Noise 1Unusual Noise Continuous and IncreasingEC-1200 EC-1600 EC-3600 Flywheel set with new onesUnusual Noise Periodical 2Unusual NoiseNoise occurs when the pedal is rotated with a large torque 3Unusual Noise1Removing the Frame Covers 1Removing the Frame Covers2Removing the Frame Covers Remove the frame covers in the following proceduresRemoving the Frame Covers Side pedal can be removed by turning it in the clockwiseES-1Replacing the Wiring within FrameES-2Replacing the 5P Cable 2Replacing the 5P CableFrame Covers Control unit. Also, remove the cable connector. FigCable to the frame by using cable holders Cut the cable holders which fix the cable to remove the 5PES-3Replacing the Power ES-3Replacing the Power Supply BoardSupply Board Frame side Fig Metal base in the following procedures. FigWhen the main unit is viewed from the direction as depicted , fasten the frame-side nutES-5Replacing the CDC Sensor ES-5Replacing the CDC SensorES-6Replacing the Panel Keyboard Replacing the Panel KeyboardES-7Replacing the Button Panel ES-7Replacing the Button PanelReplacing the Printer ES-8Replacing the PrinterES-9Adjusting the Printing Darkness ES-9Adjusting the Printing DarknessPaper Jamming in Printer ES-10Paper Jamming in PrinterMS-1Replacing Workload Unit w/o FlywheelEC-1200 Assemble the chain. Chain should first be set on the free Wheel before setting it to the upper part of the large gearSetting on the large gear. Fig Tension to the chain. FigMS-1Replacing the Workload Unit w/o Flywheel MS-2Replacing the Workload Unit FlywheelÀMounting the Brandnew Workload Unit MS-3Adjusting the Flywheel MS-3Adjusting the FlywheelEC-1600 EC-3600 MS-4Replacing the Chain MS-5Replacing the Free Wheel Set MS-5Replacing the Free Wheel SetMS-6Replacing the Derailleur Set MS-7Replacing the Idler Set MS-7Replacing the Idler SetMS-8Replacing the Crank Set MS-8Replacing the Crank SetShould be adjusted as illustrated in Fig Fasten the crank cap by using a coin, etc. FigEnable the complete setting of the gear. Fig Adjust the clearance between the magnet mounted onMS-9Replacing the BB Set 9Replacing the BB SetMS-10Replacing the Post Spacer MS-10Replacing the Post SpacerMS-11Adjusting the Spacer Spring MS-11Adjusting the Spacer SpringMS-12Replacing the Inner Pipe Spacer MS-12Replacing the Inner Pipe SpacerMS-13Replacing the Vertical Pipe Spacer EC-3600 EC-3700 MS-13Replacing the Vertical Pipe SpacerMS-14Replacing the Leg Cover MS-14Replacing the Leg CoverEC-3600 EC-3700 MS-15Replacing the Caster and Level Adjuster MS-16Replacing the Seat Post Knob MS-16Replacing the Seat Post KnobMS-17Replacing the Lock Pin EC-3600 EC-3700 MS-17Replacing the Lock PinÀREMOVAL Remove both right and left pedals. Fig MS-18Replacing the Crank CoverMS-19Replacing the Crank Cover Set the right and left pedalsEC-1200 EC-1600 MS-19Replacing the Center Cover of Upright Type1200, remove the cable holder from the handlebar post MS-20Replacing the Center Cover of Recumbent Type MS-21Replacing the Handlebar Grip MS-22Replacing the Printer Cover MS-22Replacing the Printer CoverMS-23Replacing the Paper Cutter MS-23Replacing the Paper CutterList of Genuin Parts PNR.780-5160 EC-1600/3700 Panel Keybord unit setsApplicable Models EC-1200EC-1600 PNR.781-5520 EC-3600 Crank CoverL,RSet unit sets Unit sets PNR.781-5580 Unit sets 1000 PNR.701-6701 Wireless Heart Rate Senaor Kit TMParts PNR.000-0000 HR Senaor Belt unit setsUnit sets Unit pieces P8M15-1192 PNR.724-1022 Applicable Models EC-1200B EC-1600B EC-3600B EC-3700BList of Genuin Parts Belt Drive Unit pieces P8M15-1080List of Genuin Parts Applicable Models EC-1200 EC-1600 EC-3600 EC-3700