JVC RX-DP20VBKC manual Zone 1 Main Room Operations, Turning the Power On and Off Standby

STANDBY

STANDBY / ON

Zone 1 (Main Room) Operations

This section explains only the operations commonly used when you play any sound source in Zone 1 (main room). See pages 29 to 32 for the Zone 2 (sub-room) operations.

•Before performing Zone 1 operations, it is recommended to finish the basic settings on pages 35 to 44.

IMPORTANT:

Check the following before or while using the buttons and controls.

For Zone 1 operations:

The ZONE 1 ON/OFF lamp on the unit is lit.

• When using the unit:	DOOR
	DOWN

–“ZONE 2” is not shown in the main display.

–Press DOOR DOWN to use the buttons inside the front door.

To close the front door, press DOOR UP.

•When using the remote control:

–Set the ZONE 1/ZONE 2 (LEARN/TRANSMIT) selector to “ZONE 1.”

–Check the indication shown on the remote’s display when you press a button—this indicates the remote control operation mode together with multi-room operation mode (either ZONE 1 or ZONE 2) for a while.

		LEARN TRANSMIT
			STANDBY	ON
		ZONE 1	ZONE 2
LEARN TRANSMIT		ZONE 1	ZONE 2 TV/CATV/DBS	VCR 1
		ON/OFF	ON/OFF
			STANDBY/ON	STANDBY/ON
ZONE 1	ZONE 2	ZONE 1

Ex. When you press FM/AM with ZONE 1/ZONE 2 (LEARN/TRANSMIT) selector set to “ZONE 1.”

Turning the Power On and Off (Standby)

On the unit:
To turn on the power, press	(STANDBY/ON).

The STANDBY lamp goes off, and the ZONE 1 ON/OFF lamp lights up. The front door moves down (so that the source selecting buttons appear).

STANDBY

	ZONE 1
STANDBY / ON	ON/OFF

To turn off the power (into standby mode),

press (STANDBY/ON) again.

The STANDBY lamp lights up, and the front door automatically closes. (The ZONE 1 ON/ OFF and/or ZONE 2 ON/OFF lamp goes off.)

•A small amount of power is consumed in standby mode. To turn the power off completely, unplug the AC power cord.

From the remote control:

STANDBY ON

To turn on the power, press

AUDIO (ON).

The STANDBY lamp goes off, and the ZONE 1 ON/OFF lamp on the unit lights up.

The front door moves down (so that the source selecting buttons appear).

The last Zone 1 source is activated.

	ANALOG	SPEAKERS	1
L	R
SUBWFR			VOLUME

	dB
The last Surround/THX/DSP	The volume
mode appears.	level appears.

The currently selected speakers 1 and/or 2 indicator(s) also light(s) up on the display.

•If neither speakers 1 nor 2 indicator is lit on the display, see “Activating the Zone 1 Front Speakers” on page 25.

To turn off the power (into standby mode),
press AUDIO	(STANDBY).	STANDBY	ON
The STANDBY lamp lights up, and the front
door automatically closes. (The ZONE 1 ON/
OFF and/or ZONE 2 ON/OFF lamp on the unit
goes off.)

Notes:

•Before you turn off the receiver in Zone 1, make sure that no one is listening to any source in Zone 2 (the ZONE 2 ON/OFF lamp is lit on the display) since the Zone 2 sound will also be turned off unexpectedly.

•If you have turned off the receiver with the volume level set at more than level “–35 dB,” the volume level will be automatically set at level “–35 dB” next time you turn on the receiver.

The last Zone 1 source is activated.

ANALOG	SPEAKERS 1
LR
SUBWFR	VOLUME
	dB
The last Surround/THX/DSP mode	The volume
appears.	level appears.

The currently selected speakers 1 and/or 2 indicator(s) also light(s) up on the display.

•If neither speakers 1 nor 2 indicator is lit on the display, see “Activating the Zone 1 Front Speakers” on page 25.

When you turn on the TV connected to the TV SOUND/DBS jacks on the rear

This receiver automatically turns on and selects “TV” as the Zone 1 source about 5 seconds after you turn on the TV. (If you change the source name from “TV” to “DBS,” the receiver will not turn on along with the TV. See “Changing the Source Name” on page 27.)

22