JVC RX-DP20VBKC manual For the main unit

Page 3

Note to CATV system installer:

This reminder is provided to call the CATV system installer’s attention to Section 820-40 of the NEC which provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

For the main unit:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the manufacturer for compliance could void the user’s authority to operate the equipment.

For the remote control:

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the manufacturer for compliance could void the user’s authority to operate the equipment.

G-2

Page 2 Page 4
Image 3
Page 2 Page 4
Contents LVT0965-001AJ RX-DP20VBK23.5 kg / 52.0 lb For the main unit Introduction Features PrecautionsTable of Contents To open the front door Parts IdentificationFront Panel Display Window96/24 indicator Dual indicatorAnalog indicator Dgtl Auto indicatorRear Panel Q w e r tRemote Control Getting Started Before InstallationChecking the Supplied Accessories Connecting the FM and AM AntennasTurn the loop until you have the best reception Connecting the SpeakersBasic connecting procedure AM Antenna ConnectionsZone 1 speaker layout Front speakers and center speakerSurround and surround back speakers Connecting a subwoofer Enhance your audio systemAbout the Front 2/ZONE 2 Speakers terminals Analog Connections Connecting Audio/Video ComponentsVideo camera When attaching the front Terminal coverWhen using the digital input terminal External 7.1-channel Output componentVHS/S-VHS/VHS F G VCR VCRsDBS tuner TV and/or DBS tunerWhen you connect the DVD player with stereo output jacks DVD playerDVD player Digital Connections Digital output terminalDigital input terminals Setting Up the IR Signal Transmitter Using the RF Rod Antenna and IR Signal TransmitterFind a place where you can attach the IR signal transmitter Setting Up the RF Rod AntennaReplace the cover Putting Batteries in the Remote ControlConnecting the Power Cord When using the remote control in the darkConnection Å Connection ı Power amplifierMulti-Room Operations Required Connections for ZoneBasic Operating Procedure for Zone Press Zone 2 Control so that Control Turn Master Volume toPress Zone 2 ON/OFF so that Zone 2 ON/OFF lamp lights upZone 1 Main Room Operations Turning the Power On and Off StandbyTo turn on the power, press To turn off the power into standby modePress one of the source selecting buttons Canceling the Zone 1 OperationsSpeaker and signal indicators on the display Selecting the Zone 1 Source to PlaySelecting different sources for picture and sound Adjusting the Zone 1 VolumeSelecting the Analog or Digital Input Mode Activating the Zone 1 Front SpeakersMode Attenuating the Input Signal Muting the Zone 1 SoundAnalog Changing the Source Name Changing the Display BrightnessMaking Sounds Natural Turning Analog Direct On and OffRecording a Source Using the Sleep TimerBasic adjustment auto memory Press Sleep repeatedlyFront door so that Zone Last Zone Zone 2 volume Source appearsZone 2 Sub-room Operations Press Zone 2 Control insideTo use this receiver for Zone 2 operations Canceling the Zone 2 OperationsZone 2 Speakers terminal, see also w Setting the Zone To stop Zone 2 operations and sounds throughDown Adjusting the Zone 2 VolumeSelecting the Zone 2 Source to Play DVDTo deactivate the Zone 2 front speakers, press Zone 2 again Activating the Zone 2 Front SpeakersFront speakers Muting the Zone 2 SoundPress FM/AM Tuning in to Stations ManuallyEx. When you press FM/AM With Zone 1/ZONE Receiving Radio BroadcastsSelecting the FM Reception Mode Using Preset TuningSetup Menu Configuration Basic SettingsOperation through On-Screen Display Menus Menu operation buttonsButton To do Menu Operating Procedure Press Setup MenuPress SET 1SPK Setting the Speakers-SPEAKER SettingAdjusting the Speaker Channel Output Levels-CHANNEL Level YESFront R Level AutoOFF Front L LevelLFE Setting the Speaker DistanceSetting the Bass Sounds-SUBWOOFER For each speakerSetting the THX Audio-THX Audio Setup ApartClose Selecting the Dual Mono Sound-DUAL Mono Setting the Surround Channel Output Speakers-SURR CH OUTSetting the Audio Delay Level-AUDIO Delay Setting the Digital Input/Output TerminalsPCM Setting the Video Input TerminalsSetting the Zone 2/Speakers 2 Usage Turning On and Off the Video OutputText Memorizing the Volume Level for Each Source-ONE Touch OPESuperimposing the Menus-SUPERIMPOSE Showing the Text Information on the Display-FL DisplayMidnight Mode Sound AdjustmentsAdjustment Menu Configuration Adjust MenuDisplay or erase the Adjustment Menu Select a submenu on the Adjustment MenuOr an item on a submenu downwards or Same submenu Press # or @ Right or Left to set Press Adjust MenuEx.When adjusting the DSP effects Set other items on the same submenu if necessaryMID Adjustment procedureSubmenu items BassSetting the Midnight Mode-MIDNIGHT Mode Adjusting the Various EffectsWhen one of the DSP modes except ALL CH Stereo is activated Overall level of the effect 1 to When Dolby Pro Logic II Music is activatedWhen Neo6 Music is activated Press Liveness repeatedly to adjustUsing the Surround and THX Modes Reproducing Theater AmbienceIntroducing the Surround and THX Modes DTS Extended Surround DTS-ES Dolby Digital EXDolby Pro Logic DTS Digital SurroundSurround and THX Modes Applicable to the Various Software ZoneES/EX/7.1 Available Available THX Mode Incoming Signal Type 2-channel Available Surround ModeEXES7.1 on Activating the Surround and THX ModesAbout Dialog Normalization Activating the 7.1-channel reproductionTo adjust the speaker output level using the remote control Press Surround to activate the Surround ModeTo cancel the Surround mode Ex. When Dolby Digital is activated3D Headphone Mode Press THX to activate the THX modeTo cancel the THX mode without canceling the Surround mode To cancel the THX and Surround modesIntroducing the DSP Modes Using the DSP ModesHeadphone Mode Reproducing the Sound FieldActivating the DSP Modes To adjust the DSP effectsTo cancel the DSP modes Press Effect repeatedly to adjust the levelUsing the Analog Multi-channel Playback Mode Activating the Analog Multi-channelPlayback Modes CD recorder Compu Link Remote Control SystemRemote Control through the Remote Sensor on the Receiver MD recorderAt the same time Automatic Power Off StandbyWhen you turn off the Zone 1 sound by pressing When you turn off the Zone 2 source by pressingDisc Search Only for CD Player Text Compu Link Remote Control SystemRX-DP20VBK Displaying the Disc Information on the TV screenZone 2 Learn Press Text Display while CD or MD is selected as the sourceDisc Information screen To exit from the Disc information screenPress SET again Press Text Display while CD is selected as the sourcePress % / fi to move to SEARCH, then press Press % / fi to move to Performer Then press SETEntering the Disc Information Press % / fi to move to SEARCH, then press SETPress % / fi to move To GENRE, then Press SET Press % / fi to move to Title INPUT, then press SETPress % / fi to move to Title Input Then press SET Enter the disc title, referring to steps 3Press % / fi to move to the genre you want, then press SET Press Text Display while MD is selected as the sourceConnections 2 AV Compu Link Connection AV Compu Link Remote Control SystemConnections 1 IR Signal Transmitter Connection IR signal transmitterConnections 3 Video Cable Connection CaseOne-Touch Video Play One-Touch DVD Play Automatic Power On/Off StandbyAutomatic Power On When you turn off the Zone 2 sound by pressingSound control section Amplifier Operating JVC’s Audio/Video ComponentsOperating Audio Components TunerCD recorder CD playerCD player-changer TurntableDVD player Operating Video ComponentsVCR VCR connected to the VCR 1 jacks ¶ RECOperating Other Manufacturers’ Equipment Changing the Preset Signal CodesButtons 1-9, Enter a manufacturer’s code usingPress and hold VCR Press VCRPress and hold Audio ON. Standby on Press CD Press and hold Audio Standby Press DVDRelease Audio on Release Audio StandbyManufacturer Codes Manufactures’ codes for DBS tuner Manufacturer CodesManufactures’ codes for Catv converter Manufacturer Codes Manufactures’ codes for VCRZone 1/ZONE 2 selector to Storing the Remote Signals ManuallyTo store the signals Set the LEARN/TRANSMITFor the Zone 1 operations ControlTo use the stored signals To erase the stored signalsPress the desired button Surround/THX TroubleshootingProblem Possible Cause Solution Multi-room operations Zone1/ZoneGeneral FM/AMHarmonic distortion SpecificationsPer channel, min. RMS, driven into 8 Ω Hz to 20 kHz with no more than 0.02% totalGeneral VideoFM tuner IHF AM tunerLimited Warranty Authorized Service Centers RX-DP20VBK AUDIO/VIDEO Control Receiver

RX-DP20VBKC specifications

The JVC RX-DP20VBKC is a versatile and high-performance audio receiver designed to enhance the home entertainment experience. It combines advanced technology with user-friendly features, making it an excellent choice for music enthusiasts and movie lovers alike.

One of the standout features of the RX-DP20VBKC is its powerful amplification system. With a robust output power of up to 100 watts per channel, this receiver is capable of driving a wide range of speakers, providing rich and dynamic sound quality across various genres of music. The receiver supports a variety of audio formats, ensuring compatibility with different media sources.

The RX-DP20VBKC is equipped with Bluetooth technology, allowing users to stream music wirelessly from their smartphones, tablets, or other Bluetooth-enabled devices. This convenience eliminates the need for tangled cables and enhances the overall user experience. Additionally, the receiver features USB inputs, enabling direct playback from USB flash drives, and a built-in FM/AM tuner for accessing radio stations.

Another key characteristic of this model is its multi-room capability. Users can enjoy music in multiple rooms by connecting additional compatible speakers. The receiver supports various speaker configurations, making it adaptable for larger spaces or different setups.

In terms of sound processing, the RX-DP20VBKC includes several advanced audio technologies. It boasts a built-in digital signal processor that enhances sound clarity and spatial dynamics. Users can choose from various sound presets or customize their listening experience with adjustable equalizer settings. This flexibility allows for tailored sound quality that suits individual preferences.

The design of the RX-DP20VBKC is sleek and modern, featuring an intuitive front panel with easy-to-read displays and controls. The remote control enhances usability, giving users the ability to manage playback settings from a distance.

In summary, the JVC RX-DP20VBKC is a formidable audio receiver that combines power, versatility, and modern connectivity options, making it an ideal centerpiece for any home audio system. With its impressive amplification, wireless streaming capabilities, and advanced sound processing technologies, it caters to the diverse needs of today’s audio consumers.
Top Page Image Contents