JVC RX-DP20VBKC Zone 2 Sub-room Operations, Press Zone 2 Control inside, Front door so that Zone

Page 32

Zone 2 (Sub-room) Operations

This section explains only the operations used when you play a sound source in Zone 2.

See pages 22 to 28 for the Zone 1 operations.

•Before performing the Zone 2 operations, it is recommended to finish the basic settings on pages 35 to 44.

IMPORTANT:

Check the following before or while using the buttons and controls.

For Zone 2 operations:

The ZONE 2 ON/OFF lamp on the unit is lit.

•When using the unit:

– “ZONE 2” is shown in the main display.

– Press DOOR DOWN to use the buttons inside the

DOOR

DOWN

front door.

 

To close the front door, press DOOR UP.

 

•When using the remote control:

When operating the receiver using the remote control, the display on the unit always shows the Zone 1 source information though you are operating it for the Zone 2 source.

–Set the ZONE 1/ZONE 2 (LEARN/TRANSMIT) selector to “ZONE 2.”

–Check the indication shown on the remote’s display when you press a button—this indicates the remote control operation mode together with multi-room operation mode (either ZONE 1 or ZONE 2) for a while.

 

 

LEARN TRANSMIT

 

 

 

 

STANDBY

ON

 

 

ZONE 1

ZONE 2

 

LEARN

TRANSMIT

ZONE 1

ZONE 2 TV/CATV/DBS

VCR 1

ON/OFF

ON/OFF

 

 

 

 

STANDBY/ON

STANDBY/ON

ZONE 1

ZONE 2

 

ZONE 2

 

 

 

 

Ex. When you press FM/AM with ZONE 1/ZONE 2 (LEARN/TRANSMIT) selector set to “ZONE 2.”

To use the Zone 2 TV (connected to the ZONE 2 MONITOR OUT jack)

Turn on the TV and select the correct input for this receiver manually.

For those who connect the Zone 2 front speakers to the ZONE 2 PREOUT jacks through another amplifier (see page 19)

You have to determine how to adjust the volume level through the Zone 2 front speakers. (See “w Setting the Zone 2/Speakers 2 Usage—ZONE 2/SPEAKER 2” on page 43 for more details.)

To use the Zone 2 front speakers

1Turn on the other amplifier connected to the ZONE 2 PREOUT jacks.

2Adjust the volume level through the Zone 2 front speakers either on the other amplifier or on this receiver (depending on the ZONE2PREOUT setting—see page 43).

Turning the Power On and Off (Standby)

and Selecting the Zone 2 Operations

On the unit:

1. Press (STANDBY/ON).

The STANDBY lamp goes off, and the ZONE 1 ON/OFF lamp lights up.

The front door moves down so that the source selecting buttons appear.

•The unit is now activated only for Zone 1 operations.

STANDBY

STANDBY / ON

ZONE 1

ON/OFF

 

The last Zone 1 source is activated.

 

ANALOG

SPEAKERS

1

L

R

 

 

SUBWFR

 

VOLUME

 

dB

 

 

 

The last Surround/THX/DSP

The volume

mode appears.

level appears.

The currently selected speakers 1 and/or 2 indicator(s) light(s) up on the display.

2. Press ZONE 2 ON/OFF so that the

ON/OFF

 

ZONE 2

ZONE 2 ON/OFF lamp lights up.

 

• When connecting the Zone 2 front speakers to the FRONT 2/ZONE 2 SPEAKERS

terminals, see also “w Setting the Zone 2/Speakers 2 Usage—ZONE 2/SPEAKER 2” on page 43, and “Activating the Zone 2 Front Speakers” on page 32.

3. Press ZONE 2 CONTROL (inside

CONTROL

 

 

 

 

ZONE 2

 

the front door) so that “ZONE 2”

 

 

 

 

and the previously selected Zone 2

 

 

source name appear on the display.

 

 

 

 

 

 

 

 

 

SPEAKERS 1 ZONE 2

 

 

 

VOLUME

 

 

 

 

dB

 

 

 

 

The last Zone 2

The Zone 2 volume

 

source appears.

level appears.

Now the buttons and controls on the unit work for Zone 2 operations.

•Each time you press the button, the buttons and controls on the unit are activated or deactivated for Zone 2 operations.

29

Page 31 Page 33
Image 32
Page 31 Page 33
Contents RX-DP20VBK LVT0965-001AJ23.5 kg / 52.0 lb For the main unit Features Precautions IntroductionTable of Contents Parts Identification Front PanelDisplay Window To open the front doorDual indicator Analog indicatorDgtl Auto indicator 96/24 indicatorQ w e r t Rear PanelRemote Control Before Installation Checking the Supplied AccessoriesConnecting the FM and AM Antennas Getting StartedConnecting the Speakers Basic connecting procedureAM Antenna Connections Turn the loop until you have the best receptionSurround and surround back speakers Zone 1 speaker layoutFront speakers and center speaker About the Front 2/ZONE 2 Speakers terminals Connecting a subwooferEnhance your audio system Connecting Audio/Video Components Analog ConnectionsWhen attaching the front Terminal cover When using the digital input terminalExternal 7.1-channel Output component Video cameraVCRs VHS/S-VHS/VHS F G VCRTV and/or DBS tuner DBS tunerDVD player When you connect the DVD player with stereo output jacksDVD player Digital input terminals Digital ConnectionsDigital output terminal Using the RF Rod Antenna and IR Signal Transmitter Find a place where you can attach the IR signal transmitterSetting Up the RF Rod Antenna Setting Up the IR Signal TransmitterPutting Batteries in the Remote Control Connecting the Power CordWhen using the remote control in the dark Replace the coverPower amplifier Multi-Room OperationsRequired Connections for Zone Connection Å Connection ıBasic Operating Procedure for Zone Turn Master Volume to Press Zone 2 ON/OFF so thatZone 2 ON/OFF lamp lights up Press Zone 2 Control so that ControlTurning the Power On and Off Standby To turn on the power, pressTo turn off the power into standby mode Zone 1 Main Room OperationsCanceling the Zone 1 Operations Speaker and signal indicators on the displaySelecting the Zone 1 Source to Play Press one of the source selecting buttonsAdjusting the Zone 1 Volume Selecting different sources for picture and soundMode Selecting the Analog or Digital Input ModeActivating the Zone 1 Front Speakers Analog Attenuating the Input SignalMuting the Zone 1 Sound Changing the Display Brightness Making Sounds NaturalTurning Analog Direct On and Off Changing the Source NameUsing the Sleep Timer Basic adjustment auto memoryPress Sleep repeatedly Recording a SourceLast Zone Zone 2 volume Source appears Zone 2 Sub-room OperationsPress Zone 2 Control inside Front door so that ZoneCanceling the Zone 2 Operations Zone 2 Speakers terminal, see also w Setting the ZoneTo stop Zone 2 operations and sounds through To use this receiver for Zone 2 operationsAdjusting the Zone 2 Volume Selecting the Zone 2 Source to PlayDVD DownActivating the Zone 2 Front Speakers Front speakersMuting the Zone 2 Sound To deactivate the Zone 2 front speakers, press Zone 2 againTuning in to Stations Manually Ex. When you press FM/AM With Zone 1/ZONEReceiving Radio Broadcasts Press FM/AMUsing Preset Tuning Selecting the FM Reception ModeBasic Settings Setup Menu ConfigurationButton To do Operation through On-Screen Display MenusMenu operation buttons Press SET Menu Operating ProcedurePress Setup Menu Setting the Speakers-SPEAKER Setting Adjusting the Speaker Channel Output Levels-CHANNEL LevelYES 1SPKAuto OFFFront L Level Front R LevelSetting the Speaker Distance Setting the Bass Sounds-SUBWOOFERFor each speaker LFEClose Setting the THX Audio-THX Audio SetupApart Setting the Surround Channel Output Speakers-SURR CH OUT Setting the Audio Delay Level-AUDIO DelaySetting the Digital Input/Output Terminals Selecting the Dual Mono Sound-DUAL MonoSetting the Video Input Terminals Setting the Zone 2/Speakers 2 UsageTurning On and Off the Video Output PCMMemorizing the Volume Level for Each Source-ONE Touch OPE Superimposing the Menus-SUPERIMPOSEShowing the Text Information on the Display-FL Display TextSound Adjustments Adjustment Menu ConfigurationAdjust Menu Midnight ModeOr an item on a submenu downwards or Display or erase the Adjustment MenuSelect a submenu on the Adjustment Menu Press Adjust Menu Ex.When adjusting the DSP effectsSet other items on the same submenu if necessary Same submenu Press # or @ Right or Left to setAdjustment procedure Submenu itemsBass MIDWhen one of the DSP modes except ALL CH Stereo is activated Setting the Midnight Mode-MIDNIGHT ModeAdjusting the Various Effects When Dolby Pro Logic II Music is activated When Neo6 Music is activatedPress Liveness repeatedly to adjust Overall level of the effect 1 toIntroducing the Surround and THX Modes Using the Surround and THX ModesReproducing Theater Ambience Dolby Digital EX Dolby Pro LogicDTS Digital Surround DTS Extended Surround DTS-ESES/EX/7.1 Available Surround and THX Modes Applicable to the Various SoftwareZone Incoming Signal Type 2-channel Available Surround Mode Available THX ModeActivating the Surround and THX Modes About Dialog NormalizationActivating the 7.1-channel reproduction EXES7.1 onPress Surround to activate the Surround Mode To cancel the Surround modeEx. When Dolby Digital is activated To adjust the speaker output level using the remote controlPress THX to activate the THX mode To cancel the THX mode without canceling the Surround modeTo cancel the THX and Surround modes 3D Headphone ModeUsing the DSP Modes Headphone ModeReproducing the Sound Field Introducing the DSP ModesTo adjust the DSP effects To cancel the DSP modesPress Effect repeatedly to adjust the level Activating the DSP ModesPlayback Modes Using the Analog Multi-channel Playback ModeActivating the Analog Multi-channel Compu Link Remote Control System Remote Control through the Remote Sensor on the ReceiverMD recorder CD recorderAutomatic Power Off Standby When you turn off the Zone 1 sound by pressingWhen you turn off the Zone 2 source by pressing At the same timeText Compu Link Remote Control System RX-DP20VBKDisplaying the Disc Information on the TV screen Disc Search Only for CD PlayerPress Text Display while CD or MD is selected as the source Disc Information screenTo exit from the Disc information screen Zone 2 LearnPress Text Display while CD is selected as the source Press % / fi to move to SEARCH, then pressPress % / fi to move to Performer Then press SET Press SET againPress % / fi to move to SEARCH, then press SET Press % / fi to move To GENRE, then Press SETPress % / fi to move to Title INPUT, then press SET Entering the Disc InformationEnter the disc title, referring to steps 3 Press % / fi to move to the genre you want, then press SETPress Text Display while MD is selected as the source Press % / fi to move to Title Input Then press SETAV Compu Link Remote Control System Connections 1 IR Signal Transmitter ConnectionIR signal transmitter Connections 2 AV Compu Link ConnectionOne-Touch Video Play Connections 3 Video Cable ConnectionCase Automatic Power On/Off Standby Automatic Power OnWhen you turn off the Zone 2 sound by pressing One-Touch DVD PlayOperating JVC’s Audio/Video Components Operating Audio ComponentsTuner Sound control section AmplifierCD player CD player-changerTurntable CD recorderOperating Video Components VCR VCR connected to the VCR 1 jacks¶ REC DVD playerChanging the Preset Signal Codes Operating Other Manufacturers’ EquipmentEnter a manufacturer’s code using Press and hold VCRPress VCR Buttons 1-9,Press and hold Audio Standby Press DVD Release Audio onRelease Audio Standby Press and hold Audio ON. Standby on Press CDManufactures’ codes for DBS tuner Manufacturer Codes Manufactures’ codes for Catv converter Manufacturer CodesManufactures’ codes for VCR Manufacturer CodesStoring the Remote Signals Manually To store the signalsSet the LEARN/TRANSMIT Zone 1/ZONE 2 selector toControl For the Zone 1 operationsPress the desired button To use the stored signalsTo erase the stored signals Troubleshooting Problem Possible Cause SolutionMulti-room operations Zone1/Zone Surround/THXFM/AM GeneralSpecifications Per channel, min. RMS, driven into 8 ΩHz to 20 kHz with no more than 0.02% total Harmonic distortionVideo FM tuner IHFAM tuner GeneralLimited Warranty Authorized Service Centers RX-DP20VBK AUDIO/VIDEO Control Receiver

RX-DP20VBKC specifications

The JVC RX-DP20VBKC is a versatile and high-performance audio receiver designed to enhance the home entertainment experience. It combines advanced technology with user-friendly features, making it an excellent choice for music enthusiasts and movie lovers alike.

One of the standout features of the RX-DP20VBKC is its powerful amplification system. With a robust output power of up to 100 watts per channel, this receiver is capable of driving a wide range of speakers, providing rich and dynamic sound quality across various genres of music. The receiver supports a variety of audio formats, ensuring compatibility with different media sources.

The RX-DP20VBKC is equipped with Bluetooth technology, allowing users to stream music wirelessly from their smartphones, tablets, or other Bluetooth-enabled devices. This convenience eliminates the need for tangled cables and enhances the overall user experience. Additionally, the receiver features USB inputs, enabling direct playback from USB flash drives, and a built-in FM/AM tuner for accessing radio stations.

Another key characteristic of this model is its multi-room capability. Users can enjoy music in multiple rooms by connecting additional compatible speakers. The receiver supports various speaker configurations, making it adaptable for larger spaces or different setups.

In terms of sound processing, the RX-DP20VBKC includes several advanced audio technologies. It boasts a built-in digital signal processor that enhances sound clarity and spatial dynamics. Users can choose from various sound presets or customize their listening experience with adjustable equalizer settings. This flexibility allows for tailored sound quality that suits individual preferences.

The design of the RX-DP20VBKC is sleek and modern, featuring an intuitive front panel with easy-to-read displays and controls. The remote control enhances usability, giving users the ability to manage playback settings from a distance.

In summary, the JVC RX-DP20VBKC is a formidable audio receiver that combines power, versatility, and modern connectivity options, making it an ideal centerpiece for any home audio system. With its impressive amplification, wireless streaming capabilities, and advanced sound processing technologies, it caters to the diverse needs of today’s audio consumers.
Top Page Image Contents