Weider 831.159380 user manual Long Cable Trap is positioned to hold the Cable in place

Page 12

CABLE ASSEMBLY

20.Wrap the High Cable (58) around a “V”-Pulley (50). Attach the “V”-Pulley and a Long Cable Trap (31) to the indicated bracket on the Front Upright (42) with a 3/8” x 2 1/2” Bolt (86) and a 3/8” Nylon Locknut (21). Be sure that the

Long Cable Trap is positioned to hold the Cable in place.

21.Route the High Cable (58) around the “V”- Pulley (50) on the Left Arm (47). Be sure that the Cable is in the groove of the Pulley and that the Long Cable Trap (31) is posi- tioned to hold the Cable in place. Tighten the 3/8” x 2 1/2” Bolt (86) and the 3/8” Nylon Locknut (not shown).

22.Route the High Cable (58) around the “V”- Pulley (50) on the Right Arm (48). Be sure that the Cable is in the groove of the “V”- Pulley and that the Long Cable Trap (31) is turned to hold the Cable in place. Tighten the 3/8” x 2 1/2” Bolt (86) and the 3/8” Nylon Locknut (not shown).

23.Attach the Pulley Bracket (20) to the Top Frame (55) with the 5/16” x 5” Bolt (68) and a 5/16” Nylon Locknut (3). Do not overtighten the Nylon Locknut; the Pulley Bracket must be able to move freely.

See the inset drawing. Route the High Cable (58) around the 3 1/2” Pulley (15) attached to the Pulley Bracket (20). Tighten the 3/8” x 2” Bolt (12) and a 3/8” Nylon Locknut (not shown). Be sure that the Cable is in the groove of the Pulley and that the Cable Trap (66) is turned to hold the Cable in place.

20

86

31

58

50

Bracket

42

21

21

86 31

50

58

47

22

31 86 50

58

48

23			68
			68
	55		66
			66
20			12
			12
		3	15
		3
			58

12

Image 12

Contents Patent Pending Model No Serial NoSEARS, Roebuck and CO., Hoffman ESTATES, IL Table of Contents Important PrecautionsUsing the Weider PRO 9645 Home Gym System Before YOU BeginFor your benefit, read this manual carefully before Assembly Frame AssemblyFollowing Tools not Included are Required for Assembly Frame AssemblyLocknuts yet Stabilizer 5. Stack eight Weights onto Stack of WeightsWeights 25 until is complete Tighten all Nylon Locknuts used in stepsTube is sitting in the pin grooves in the top Weight Be sure that the pin on the WeightWeight Be sure that the holes in the WeightLocate and open the parts bag labeled ARM Assembly Arm must be able to pivot freelyOn each Arm. Arm identification is very Important for stepDo not tighten the Nylon Locknut yet Arm with the Left Arm 47 refer to stepAssembly ARMARM Assembly Cable Assembly Long Cable Trap is positioned to hold the Cable in place Bracket Cable Cable Assembly Cable Assembly Must be inserted from the side shown That the Pulley is on the side shownThat the Cable Trap is positioned to hold Cable in placeCable Assembly Seat Assembly Locate and open the parts bag labeled Seat AssemblySeat Rect the problem. Important If the cables Are not properly installed, they may beDamaged when heavy weight is used. See HOW to USE the Home GYM System Changing the Weight SettingAdjusting the LEG Press Plate Attaching and Removing the SeatAttaching the LEG Lever to the LOW Pulley Station Weight Resistance Chart PlatesTROUBLE-SHOOTING and Maintenance Tightening the CablesCable Diagrams High Cable 58 and Low CableHigh Cable Low CableMilitary Press Cable 72 and Leg Press Cable Pivot Arm Leg Press CablePage Page X 3 1/4 Bolt R1096A Key Part Qty DescriptionKey Part Exploded DRAWING-Model No Full 90 DAY Warranty Model NoSEARS, Roebuck and CO., Dept WA, Hoffman ESTATES, IL