Weider 831.159380 user manual Bracket

Page 13

CABLE ASSEMBLY

24.See the inset drawing. Attach a 3 1/2” Pulley

(15)and a Cable Trap (66) to the upper hole in a Long “U”-Bracket (57) with a 3/8” x 2” Bolt

(12)and a 3/8” Nylon Locknut (21). Be sure that the Cable Trap is inside the Long “U”- Bracket. Note: This may come pre-assem- bled.

Route the High Cable (58) through the Long “U”-Bracket (57) and the 3 1/2” Pulley (15) shown in the inset drawing. Be sure that the

Cable is in the groove of the Pulley and that the Cable and Pulley move smoothly.

25.Wrap the High Cable (58) around a 3 1/2” Pulley (15). Attach the Pulley to the bracket on the Top Frame (55) with a 3/8” x 2” Bolt (12) and a 3/8” Nylon Locknut (21). Be sure that the Cable is in the groove of the Pulley and that the Cable and Pulley move smoothly.

26.Note: This assembly step shows how to complete the assembly of several pre- attached parts.

The 5/8” x 9/16” Spacer (7) has been pre- attached on the outside of the 3 1/2” Low Pulley (102) for shipping purposes. Remove the 3/8” Nylon Locknut (21), the Spacer, and the Pulley from the 3/8” x 3 3/4” Bolt (88). Do not remove the Bolt. The Bolt has been shown removed for part identification.

Reattach the 3 1/2” Low Pulley (102), with the 5/8” x 9/16” Spacer (7) between the Pulley and the Press Frame (17). Do not tighten the 3/8”

Nylon Locknut (21) yet. Be sure that the 3/8” x 3 3/4” Bolt (88), the 3/8” Flat Washer (9), the 5/8” x 9/16” Spacer (7), the 3 1/2” Low Pulley (102), and the 3/8” Nylon Locknut (21) are oriented as shown.

24

58

66

15

21

 

15

57

12

58

 

 

 

 

57

 

25

 

 

 

Bracket

12

55

 

58

 

 

 

 

15

21

26

9 88

7

17 102

21

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Model No Serial No Patent PendingSEARS, Roebuck and CO., Hoffman ESTATES, IL Important Precautions Table of ContentsBefore YOU Begin Using the Weider PRO 9645 Home Gym SystemFor your benefit, read this manual carefully before Frame Assembly AssemblyFollowing Tools not Included are Required for Assembly Frame AssemblyLocknuts yet Stack of Weights Stabilizer 5. Stack eight Weights ontoWeights 25 until is complete Tighten all Nylon Locknuts used in stepsBe sure that the pin on the Weight Tube is sitting in the pin grooves in the top WeightWeight Be sure that the holes in the WeightArm must be able to pivot freely Locate and open the parts bag labeled ARM AssemblyImportant for step On each Arm. Arm identification is veryDo not tighten the Nylon Locknut yet Arm with the Left Arm 47 refer to stepARM AssemblyARM Assembly Cable Assembly Long Cable Trap is positioned to hold the Cable in place Bracket Cable Cable Assembly Cable Assembly That the Pulley is on the side shown Must be inserted from the side shownThat the Cable Trap is positioned to hold Cable in placeCable Assembly Locate and open the parts bag labeled Seat Assembly Seat AssemblySeat Are not properly installed, they may be Rect the problem. Important If the cablesDamaged when heavy weight is used. See Changing the Weight Setting HOW to USE the Home GYM SystemAttaching and Removing the Seat Adjusting the LEG Press PlateAttaching the LEG Lever to the LOW Pulley Station Plates Weight Resistance ChartTightening the Cables TROUBLE-SHOOTING and MaintenanceHigh Cable 58 and Low Cable Cable DiagramsHigh Cable Low CableLeg Press Cable Military Press Cable 72 and Leg Press Cable Pivot ArmPage Page X 3 1/4 Bolt Key Part Qty Description R1096AKey Part Exploded DRAWING-Model No Model No Full 90 DAY WarrantySEARS, Roebuck and CO., Dept WA, Hoffman ESTATES, IL
Top Page Image Contents