Weider 831.159380 user manual Locate and open the parts bag labeled ARM Assembly

Page 8

FRAME ASSEMBLY

9.Attach the upper ends of the Short Weight Guides (73) to the Top Frame (55) with a 5/16” x 6” Bolt (60), two 1/2” x 3/4” Spacers (61), and a 5/16” Nylon Locknut (3).

Attach the upper ends of the Long Weight Guides (62) to the Top Frame (55) in the same manner.

10.Locate and open the parts bag labeled “ARM ASSEMBLY.”

Be sure there is a Bushing (98) in each side of the Stabilizer (5). Press a 2” Square Inner Cap (27) into each end of the Leg Press Arm (96).

9
		61
						61
				3		61

	3
60	55
60

73

60

62

10	95	27

Welded

Tube

Lubricate a 3/8” x 3 1/4” Bolt (67). Attach the Leg Press Arm (96) to the Stabilizer (5) with the Bolt and a 3/8” Nylon Locknut (21). Do not over- tighten the Nylon Locknut. The Leg Press

96

97

21 27

67—Lubricate

ARM ASSEMBLY

Arm must be able to pivot freely.

Align the welded tubes on the Leg Press Plate

(95)with one set of holes in the Leg Press Arm

(96).Attach the Leg Press Plate to the Leg Press Arm with the Press Pin (97).

11.Press a 1” x 7/8” Plastic Bushing (90) onto each welded spacer on the Press Frame (17). Slide the Press Frame into place onto the Base

(4).Note: This will be a tight fit. The Plastic Bushings should fit on each end of the indi- cated tube in the Base. Make sure that the pulleys are on the side shown.

Lubricate the 3/8” x 8” Bolt (59). Attach the Press Frame (17) to the Base (4) with the Bolt and a 3/8” Nylon Locknut (21).

5	27

98

11
17	Pulleys

must be on

this side 59—Lubricate

21	Welded Spacers

4

90

Tube

8

Image 8

Contents SEARS, Roebuck and CO., Hoffman ESTATES, IL Patent PendingModel No Serial No Table of Contents Important PrecautionsFor your benefit, read this manual carefully before Using the Weider PRO 9645 Home Gym SystemBefore YOU Begin Assembly Frame AssemblyFollowing Tools not Included are Required for Assembly Frame AssemblyLocknuts yet Stabilizer 5. Stack eight Weights onto Stack of WeightsWeights 25 until is complete Tighten all Nylon Locknuts used in stepsTube is sitting in the pin grooves in the top Weight Be sure that the pin on the WeightWeight Be sure that the holes in the WeightLocate and open the parts bag labeled ARM Assembly Arm must be able to pivot freelyOn each Arm. Arm identification is very Important for stepDo not tighten the Nylon Locknut yet Arm with the Left Arm 47 refer to stepAssembly ARMARM Assembly Cable Assembly Long Cable Trap is positioned to hold the Cable in place Bracket Cable Cable Assembly Cable Assembly Must be inserted from the side shown That the Pulley is on the side shownThat the Cable Trap is positioned to hold Cable in placeCable Assembly Seat Assembly Locate and open the parts bag labeled Seat AssemblySeat Damaged when heavy weight is used. See Rect the problem. Important If the cablesAre not properly installed, they may be HOW to USE the Home GYM System Changing the Weight SettingAttaching the LEG Lever to the LOW Pulley Station Adjusting the LEG Press PlateAttaching and Removing the Seat Weight Resistance Chart PlatesTROUBLE-SHOOTING and Maintenance Tightening the CablesCable Diagrams High Cable 58 and Low CableHigh Cable Low CableMilitary Press Cable 72 and Leg Press Cable Pivot Arm Leg Press CablePage Page X 3 1/4 Bolt Key Part R1096AKey Part Qty Description Exploded DRAWING-Model No SEARS, Roebuck and CO., Dept WA, Hoffman ESTATES, IL Full 90 DAY WarrantyModel No