Weider 831.159380 user manual On each Arm. Arm identification is very, Important for step, Drawing

Page 9

12.Press a 1” Round Inner Cap (49) into one of the Press Arms (46). Press a 1 3/4” Square Inner Cap (44) into the Press Arm.

Attach the Press Arm (46) to one side of the Press Frame (17) with two 5/16” x 2 1/2” Bolts (22) and two 5/16” Nylon Locknuts (3).

Assemble the other Press Arm (46) in the same manner.

12	44	49
		49

46

22

46

3

17

13. Identify the Right Arm (48) and the Left Arm

(47). Note the position of the welded bracket

on each Arm. Arm identification is very

important for step 14.

Attach a “V”-Pulley (50) and a Long Cable

Trap (31) to the Right Arm (48) with a 3/8” x

2 1/2” Bolt (86) and a 3/8” Nylon Locknut (21).

Do not tighten the Nylon Locknut yet.

Attach a “V”-Pulley (50) and a Long Cable

13

86

31

50

Welded

Brackets

31

50

47

21

ARM ASSEMBLY

Trap (31) to the Left Arm (47) in the same

manner.

14. Lubricate both axles on the Top Frame (55).

Slide the Right Arm (48) onto the right axle.

Note: Be careful not to confuse the Right

Arm with the Left Arm (47); refer to step 13

to identify the Right Arm. Be sure that the

upper end of the Right Arm is behind the

indicated bracket on the Top Frame (55).

Tap two 1” Retainers (69) and a 1” Round

Cover Cap (70) onto the axle. Be sure that

the teeth on the Retainers bend toward the

Round Cover Cap, as shown in the inset

drawing.

Attach the Left Arm (47) in the same manner.

Press 1 3/4” Square Inner Caps (44) into the

lower ends of the Right and Left Arms (47,

48). Wet the lower end of each Arm with

soapy water. Slide a 10” Pad (45) onto the

lower end of each Arm.

48

14

55 Bracket

47

Lubricate

Axle

48

69

45

70

44

44			Axle

45	69
	70

9

Image 9

Contents Patent Pending Model No Serial NoSEARS, Roebuck and CO., Hoffman ESTATES, IL Important Precautions Table of ContentsUsing the Weider PRO 9645 Home Gym System Before YOU BeginFor your benefit, read this manual carefully before Frame Assembly AssemblyFollowing Tools not Included are Required for Assembly Frame AssemblyLocknuts yet Stack of Weights Stabilizer 5. Stack eight Weights ontoWeights 25 until is complete Tighten all Nylon Locknuts used in stepsBe sure that the pin on the Weight Tube is sitting in the pin grooves in the top WeightWeight Be sure that the holes in the WeightArm must be able to pivot freely Locate and open the parts bag labeled ARM AssemblyImportant for step On each Arm. Arm identification is veryDo not tighten the Nylon Locknut yet Arm with the Left Arm 47 refer to stepARM AssemblyARM Assembly Cable Assembly Long Cable Trap is positioned to hold the Cable in place Bracket Cable Cable Assembly Cable Assembly That the Pulley is on the side shown Must be inserted from the side shownThat the Cable Trap is positioned to hold Cable in placeCable Assembly Locate and open the parts bag labeled Seat Assembly Seat AssemblySeat Rect the problem. Important If the cables Are not properly installed, they may beDamaged when heavy weight is used. See Changing the Weight Setting HOW to USE the Home GYM SystemAdjusting the LEG Press Plate Attaching and Removing the SeatAttaching the LEG Lever to the LOW Pulley Station Plates Weight Resistance ChartTightening the Cables TROUBLE-SHOOTING and MaintenanceHigh Cable 58 and Low Cable Cable DiagramsHigh Cable Low CableLeg Press Cable Military Press Cable 72 and Leg Press Cable Pivot ArmPage Page X 3 1/4 Bolt R1096A Key Part Qty DescriptionKey Part Exploded DRAWING-Model No Full 90 DAY Warranty Model NoSEARS, Roebuck and CO., Dept WA, Hoffman ESTATES, IL