Weider 831.159380 user manual Assembly, Cable

Page 14

27.Locate the Low Cable (23). Route the Low Cable under the 3 1/2” Low Pulley (102). Be sure that the end of the Cable with the ball is on the indicated side of the Press Frame (17) and that the Cable is between the Pulley and the crossbar on the Press Frame. Tighten the 3/8” Nylon Locknut (21) and the 3/8” x 3 3/4” Bolt (not shown).

27

21

102

23

Ball

17

Crossbar

ASSEMBLY

28.Route the Low Cable (23) around the 3 1/2” Pulley (15) attached to the lower hole in the Front Upright (42). See the inset drawing. Be sure that the Cable Trap (66) is turned to hold the Cable in place and that the Cable is routed around the Pulley as shown.

Tighten the 3/8” Nylon Locknut (21) and the 3/8” x 3 3/4” Bolt (88).

28

42

15

21

23

23 15

88

66

42

Inset shows view

from other side

CABLE

29.Route the Low Cable (23) around the 3 1/2” Pulley (15) attached to the upper hole in the Press Frame (17). Be sure that the Cable

Trap (66) is turned to hold the Cable in place and that the Cable is routed around the Pulley as shown. Tighten the 3/8” Nylon Locknut (21) and the 3/8” x 3 1/2” Bolt (not shown).

30.Route the Low Cable (23) around the 3 1/2” Pulley (15) attached to the upper hole in the Front Upright (42). See the inset drawing. Be sure that the Cable Trap (66) is turned to hold the Cable in place and that the Cable is routed around the Pulley as shown.

Tighten the 3/8” Nylon Locknut (21) and the 3/8” x 3 3/4” Bolt (88).

29

23

15

21

66

17

30						23		15

23

88

15

42	66
	42

21

Inset shows view from other side

14

Image 14

Contents SEARS, Roebuck and CO., Hoffman ESTATES, IL Patent PendingModel No Serial No Table of Contents Important PrecautionsFor your benefit, read this manual carefully before Using the Weider PRO 9645 Home Gym SystemBefore YOU Begin Following Tools not Included are Required for Assembly AssemblyFrame Assembly Frame AssemblyLocknuts yet Weights 25 until is complete Stabilizer 5. Stack eight Weights ontoStack of Weights Tighten all Nylon Locknuts used in stepsWeight Tube is sitting in the pin grooves in the top WeightBe sure that the pin on the Weight Be sure that the holes in the WeightLocate and open the parts bag labeled ARM Assembly Arm must be able to pivot freelyDo not tighten the Nylon Locknut yet On each Arm. Arm identification is veryImportant for step Arm with the Left Arm 47 refer to stepAssembly ARMARM Assembly Cable Assembly Long Cable Trap is positioned to hold the Cable in place Bracket Cable Cable Assembly Cable Assembly That the Cable Trap is positioned to hold Must be inserted from the side shownThat the Pulley is on the side shown Cable in placeCable Assembly Seat Assembly Locate and open the parts bag labeled Seat AssemblySeat Damaged when heavy weight is used. See Rect the problem. Important If the cablesAre not properly installed, they may be HOW to USE the Home GYM System Changing the Weight SettingAttaching the LEG Lever to the LOW Pulley Station Adjusting the LEG Press PlateAttaching and Removing the Seat Weight Resistance Chart PlatesTROUBLE-SHOOTING and Maintenance Tightening the CablesHigh Cable Cable DiagramsHigh Cable 58 and Low Cable Low CableMilitary Press Cable 72 and Leg Press Cable Pivot Arm Leg Press CablePage Page X 3 1/4 Bolt Key Part R1096AKey Part Qty Description Exploded DRAWING-Model No SEARS, Roebuck and CO., Dept WA, Hoffman ESTATES, IL Full 90 DAY WarrantyModel No