Weider WESY86301 user manual Plates 31. The Cable must be routed from

Page 15

CABLE ASSEMBLY

32. Route the Press Cable (88) over the indicated

32

 

 

 

3 1/2” Pulley (82) attached to the Pulley

 

31

 

 

 

 

Plates (31). The Cable must be routed from

 

 

50

 

the direction shown. Refer to the inset draw-

 

 

 

 

88

82

 

ing. Be sure that the Cable is between the

 

 

Cable Trap (80) and the Pulley, and that the

 

 

 

 

Cable Trap is positioned to hold the Cable

 

 

 

 

in place.

 

 

 

 

Tighten the 3/8” x 2” Bolt (50) and the 3/8”

 

 

 

80

 

 

 

88

Nylon Locknut (not shown).

 

 

 

 

 

 

 

33. Route the Press Cable (88) around a 3 1/2”

33

 

 

 

Pulley (82). Attach the Pulley and a Cable

 

 

 

 

 

 

 

Trap (80) to the Leg Press Upright (4) with a

 

 

 

 

3/8” x 3 1/2” Bolt (66), a 3/8” Washer (38) and

 

 

 

 

a 3/8” Nylon Jam Nut (43). Be sure that the

 

 

4

 

Cable Trap is turned to hold the Cable in

 

 

 

 

 

 

 

place.

 

 

38

43

 

 

 

 

 

 

88

 

 

 

 

82

 

 

 

66

80

 

 

 

 

 

 

34. Route the Press Cable (88) over the indicated

34

 

 

 

3 1/2” Pulley (82) attached to the Press

 

 

 

 

 

 

 

Frame (12). Tighten the 3/8” x 3 1/2” Bolt (66)

 

 

 

 

and the 3/8” Nylon Locknut (not shown).

 

 

 

 

 

 

 

82

 

 

 

88

 

80

 

 

 

66

 

 

 

 

12

 

35. Wrap the Press Cable (88) around a “V”

35

 

 

 

Pulley (81). Attach the “V” Pulley to the upper

 

 

 

 

 

50

 

bracket on the Leg Press Upright (4) with a

 

 

 

 

 

 

 

3/8” x 2” Bolt (50) and a 3/8” Nylon Jam Nut

 

 

 

81

(43).

 

 

 

 

 

 

4

 

 

 

 

 

88

 

 

43

 

 

15

Image 15
Contents QUESTIONS? Model No. WESY86301 Serial NoCustomer HOT Line Limited Warranty Table of ContentsImportant Precautions Using the Weider 8630 Training System. If you Before YOU BeginFor your benefit, read this manual carefully before Frame Assembly BAG TWO AssemblyFrame Assembly Following Tools not Included are Required for AssemblyDo not tighten the Nylon Locknuts yet Weight Tubes are in the pin grooves in the upper Weights Nylon Locknuts yet Frame Assembly ARM Assembly Press Plate and Adjustment Tube are ori- ented as shownLocate and open the parts bag labeled ARM Assembly Round Outer Cap, as shown in the inset Drawing Teeth on the Retainers bend towardARM Assembly Cable Assembly End with Cable Assembly Trap is turned to hold the Cable in place Cable Trap is turned to hold the Cable in placeCable Trap is turned to hold the Cable Place Plates 31. The Cable must be routed fromBolt. Do not tighten the Nylon Jam Nut Until step Cable Trap is positioned to hold the Cable in place Cable Assembly Be sure that the Cable Trap is in the indi- cated position Locate and open the parts bag labeled Seat Assembly Seat AssemblyMisc Changing the Weight Setting HOW to USE the Home GYM SystemAttaching the LEG Lever to the LOW Pulley Station Adjusting the LEG Press PlateAttaching the AB Strap to the AB Pulley Station Attaching and Removing the SeatPlates Weight Resistance ChartTightening the Cables TROUBLE-SHOOTING and MaintenanceCable Diagrams High Cable High Pulley-1 Weight Stack-5 Rear Cable Top Frame Part Identification CHART-Model No. WESY86301 R0899B Page Page Qty Description Part LIST-Model No. WESY86301Exploded DRAWING-Model No. WESY86301 R0899B Ordering Replacement Parts