Weider WESY86301 user manual TROUBLE-SHOOTING and Maintenance, Tightening the Cables

Page 25

TROUBLE-SHOOTING AND MAINTENANCE

Inspect and tighten all parts each time you use the home gym system. Replace any worn parts immediately. The home gym system can be cleaned using a damp cloth and mild non-abrasive detergent. Do not use solvents.

TIGHTENING THE CABLES

Woven cable, the type of cable used on the home gym system, can stretch slightly when it is first used. If there is slack in the cables before resistance is felt, the cables should be tightened. If any slack is felt when using the weight stack closest to the ab upright, both the High Cable (85) and the Low Cable (86) will need to be tight- ened. If any slack is felt when using the other weight stack, the Rear Cable (87), the Press Cable (88), and the Butterfly Cable (89) will need to be tightened.

To tighten the cables, first insert the weight pin into the mid- dle of the weight stack. Slack can be removed from these cables several ways:

See drawing 1. Tighten the 1/4” Nylon Locknut (44) that connects the end of the Press Cable (88) to the Large “U” Bracket (84).

See drawing 1. Remove the 3/8” Nylon Locknut (42) and the 3/8” x 2” Bolt (50) from the Cable Trap (80), Pulley, and Large “U” Bracket (84). Reattach the Pulley and Cable Trap to the other hole in the Large “U” Bracket. Be sure that the Cable Trap is in the proper position and that the Cable and Pulley move smoothly.

See drawing 2. Tighten the 1/4” Nylon Locknut (44) that connects the end of the High Cable (85) to the Small “U” Bracket (32).

The Rear Cable (87) can be tightened in the same manner.

See Drawing 3. If you feel additional slack while using the home gym system, the Low Cable (86) and the Press Cable (88) can be tightened further.

Remove the 3/8” x 2” Bolts (50), the 3/8” Nylon Locknuts (42), the 3 1/3” Pulleys (82), and the Cable Traps (80) from the Pulley Plates (31). Reattach the upper Pulley without the Cable Trap. Reattach the lower Pulley to the higher hole in the Pulley Plates without the Cable Trap. Keep the Cable Traps for future use. Be sure that the Cable and Pulley move smoothly.

Do not overtighten the cables. If the cables are overtight- ened, the top weight will be lifted off the weight stack.

If a cable tends to slip off the pulleys often, it may have become twisted. Remove the cable and re-install it.

1

82

80

42

8450

44

88

2

87

8532

44

32

44

3 82

42

5031

82

80

86, 88

If the cables need to be replaced, see ORDERING REPLACEMENT PARTS on the back cover of this manual.

25

Image 25
Contents Model No. WESY86301 Serial No QUESTIONS?Customer HOT Line Limited Warranty Table of ContentsImportant Precautions Before YOU Begin Using the Weider 8630 Training System. If youFor your benefit, read this manual carefully before Frame Assembly AssemblyFollowing Tools not Included are Required for Assembly Frame Assembly BAG TWODo not tighten the Nylon Locknuts yet Weight Tubes are in the pin grooves in the upper Weights Nylon Locknuts yet Press Plate and Adjustment Tube are ori- ented as shown Frame Assembly ARM AssemblyLocate and open the parts bag labeled ARM Assembly Round Outer Cap, as shown in the inset Drawing Teeth on the Retainers bend towardARM Assembly Cable Assembly End with Cable Assembly Trap is turned to hold the Cable in place Cable Trap is turned to hold the Cable in placeCable Trap is turned to hold the Cable Place Plates 31. The Cable must be routed fromBolt. Do not tighten the Nylon Jam Nut Until step Cable Trap is positioned to hold the Cable in place Cable Assembly Be sure that the Cable Trap is in the indi- cated position Locate and open the parts bag labeled Seat Assembly Seat AssemblyMisc Changing the Weight Setting HOW to USE the Home GYM SystemAttaching the AB Strap to the AB Pulley Station Adjusting the LEG Press PlateAttaching and Removing the Seat Attaching the LEG Lever to the LOW Pulley StationPlates Weight Resistance ChartTightening the Cables TROUBLE-SHOOTING and MaintenanceCable Diagrams High Cable High Pulley-1 Weight Stack-5 Rear Cable Top Frame Part Identification CHART-Model No. WESY86301 R0899B Page Page Qty Description Part LIST-Model No. WESY86301Exploded DRAWING-Model No. WESY86301 R0899B Ordering Replacement Parts