Weider WESY86301 user manual Do not tighten the Nylon Locknuts yet

Page 6

FRAME ASSEMBLY

2.Slide the Ab Upright (1) onto the indicated 5/16” x 2 1/2” Carriage Bolts (49) in the Weight Base (14). Hand tighten two 5/16” Nylon Locknuts (40) onto the Carriage Bolts.

Do not tighten the Nylon Locknuts yet.

Slide the Leg Press Upright (4) onto the indi- cated 5/16” x 2 1/2” Carriage Bolts (49) in the Weight Base (14). Hand tighten two 5/16” Nylon Locknuts (40) onto the Carriage Bolts.

Do not tighten the Nylon Locknuts yet.

3.Press a 2” Square Inner Cap (56) into each end of the Top Frame (2). Press a 2” Square Inner Cap (56) into each side of the Butterfly Frame (3). Press two 1” Round Inner Caps

(70)into the top of the Butterfly Frame.

Attach the Butterfly Frame (3) to the Top Frame (2) with a 5/16” x 3” Bolt (92). Be sure that the Bolt is on the side shown.

Finish attaching the Butterfly Frame (3) to the Top Frame (2) with a 5/16” Nylon Jam Nut (91), a 5/16” x 2 3/4” Bolt (55), a 5/16” Washer (20), and a 5/16” Nylon Locknut (40).

4.Slide the Front Seat Frame (8) onto the indi- cated 5/16” x 2 1/2” Carriage Bolts (49) in the Press Base (13). Hand tighten two 5/16” Nylon Locknuts (40) onto the Carriage Bolts.

Attach the other end of the Front Seat Frame

(8)to the Leg Press Upright (4) with two 5/16” x 2 3/4” Bolts (55), two 5/16” Washers (20), and two 5/16” Nylon Locknuts (40).

Press a 2” Square Inner Cap (56) into the Front Seat Frame (8).

6

2

 

 

 

4

 

 

 

1

 

 

 

40

 

40

 

 

 

 

14

 

13

 

 

 

 

49

49

 

 

3

 

 

 

 

 

56

 

91

 

 

 

40

 

 

 

20

92

70

56

2

 

 

 

55

 

 

3

56

56

 

 

 

 

 

4

 

 

 

40

 

 

 

55

 

 

 

20

8

 

 

 

 

 

4

 

56

13

 

40

 

 

 

 

49

 

 

 

Image 6
Contents QUESTIONS? Model No. WESY86301 Serial NoCustomer HOT Line Table of Contents Limited WarrantyImportant Precautions Using the Weider 8630 Training System. If you Before YOU BeginFor your benefit, read this manual carefully before Following Tools not Included are Required for Assembly AssemblyFrame Assembly Frame Assembly BAG TWODo not tighten the Nylon Locknuts yet Weight Tubes are in the pin grooves in the upper Weights Nylon Locknuts yet Frame Assembly ARM Assembly Press Plate and Adjustment Tube are ori- ented as shownLocate and open the parts bag labeled ARM Assembly Teeth on the Retainers bend toward Round Outer Cap, as shown in the inset DrawingARM Assembly Cable Assembly End with Cable Assembly Cable Trap is turned to hold the Cable in place Trap is turned to hold the Cable in placePlates 31. The Cable must be routed from Cable Trap is turned to hold the Cable PlaceBolt. Do not tighten the Nylon Jam Nut Until step Cable Trap is positioned to hold the Cable in place Cable Assembly Be sure that the Cable Trap is in the indi- cated position Seat Assembly Locate and open the parts bag labeled Seat AssemblyMisc HOW to USE the Home GYM System Changing the Weight SettingAttaching and Removing the Seat Adjusting the LEG Press PlateAttaching the AB Strap to the AB Pulley Station Attaching the LEG Lever to the LOW Pulley StationWeight Resistance Chart PlatesTROUBLE-SHOOTING and Maintenance Tightening the CablesCable Diagrams High Cable High Pulley-1 Weight Stack-5 Rear Cable Top Frame Part Identification CHART-Model No. WESY86301 R0899B Page Page Part LIST-Model No. WESY86301 Qty DescriptionExploded DRAWING-Model No. WESY86301 R0899B Ordering Replacement Parts