Weider WESY85201 Cable Assembly, Locate the Long Cable, A 3/8 Nylon Locknut, Cable in place

Page 10

CABLE ASSEMBLY

14.During steps 15 through 29, refer to the CABLE DIAGRAM on page 19 of this manual

to verify proper cable routing. Before begin- ning this section, identify the Long Cable (23) and the Short Cable (58) by comparing the lengths of the cables.

IMPORTANT: While assembling the cables, do not overtighten the bolts and nuts securing the pulleys. The pulleys must be able to turn freely.

15. Locate the Long Cable (23).	Route the Long
Cable around the indicated 3 1/2” Pulley (15)
attached to the Top Frame (55).	Be sure that

the end of the Cable with the ball is on the indicated side of the Pulley and that the Cable is between the Pulley and the hook.

Tighten the 3/8” x 3 3/4” Bolt (71) and the 3/8” Nylon Locknut (not shown).

16.Wrap the Long Cable (23) around a “V”-Pulley

(6). Attach the “V”-Pulley and a Long Cable Trap (50) to the indicated bracket on the

Front Upright (42) with a 3/8” x 2 1/2” Bolt (7)

and a 3/8” Nylon Locknut (21).	Be sure that
the Long Cable Trap is positioned to hold
the Cable in place.

17. Route the Long Cable (23) around the “V”-

Pulley (6) on the Left Arm (47).	Be sure that
the Cable is in the groove of the Pulley
and that the Long Cable Trap (50) is posi-
tioned to hold the Cable in place.	Tighten

the 3/8” x 2 1/2” Bolt (7) and the 3/8” Nylon Locknut (not shown).

14

23

58

15

55	23

15

Ball 71

Hook

16		7
		7
	6	50
	6
		42

23

21

17

6 7 50

47

23

10

Image 10

Contents Customer HOT Line QUESTIONS?Model No. WESY85201 Serial No Mon.-Fri., 6 a.m.-6 p.m. MSTTable of Contents Limited WarrantyIng down Important PrecautionsMake sure that the cables remain on the pul Using the Weider Before YOU BeginFollowing Tools not Included are Required for Assembly AssemblyAssembly, use the Part Identification Not tighten the Nylon Locknuts yetEach Carriage Bolt Frame AssemblyTighten all Nylon Locknuts used in steps 1 through Frame Assembly ARM Assembly ShownAttach a V-Pulley 6 and a Long Cable Trap On each Arm. Arm identification is very important for stepAttach the Left Arm 47 in the same manner Nylon Locknuts until the end of this assembly step Tighten all Nylon Locknuts used in this step nowA 3/8 Nylon Locknut Cable AssemblyLocate the Long Cable Cable in placeBracket. Note This may come pre-assem- bled Pulley 6 on the Right Arm Be sure3/8 x 2 1/2 Bolt 7 and the 3/8 Nylon Locknut not shown For easy part identificationFront Upright Locate the Short Cable Route3/8 x 3 1/2 Bolt 16 Trap 66 is turned to hold the CableTighten the 3/8 Nylon Locknut 21 and the 3/8 x 3 1/2 Bolt A 1/4 Flat Washer 10. Do not com Cable Assembly Seat AssemblySeat Plate to the Seat 13 with two 1/4 x 1/2 Screws Insert the L-Pin 40 through the holes Seat Assembly Decal Placement8520 Amount of resistance at each weight station AdjustmentChanging the Weight Setting Attaching the LAT BAR or Nylon Strap to High Pulley StationWeight Resistance Chart Locking the LEG LeverWoven cable, the type of cable used on the home TROUBLE-SHOOTING and MaintenanceTightening the Cables That the Cable and Pulley move smoothlyShort Cable Cable DiagramCable traps do not touch or bind the cables Long Cable Be sure thatOrdering Replacement Parts Part No R1096ARemove this Part Identification Chart from the Manual WESY85201 R1096AParafusode5/16x13/4 Clipe do Cabo Espaçador de 1/2 x 3/4 61-2 Remove this Part LIST/EXPLODED Drawing from the Manual Part LIST-Model No. WESY85201 Qty DescriptionR1096A