Weider WESY85201 user manual Adjustment, Changing the Weight Setting

Page 16

ADJUSTMENT

The instructions below describe how each part of the home gym system can be adjusted. Refer to the exercise poster accompanying this manual to see how the home gym system should be set up for each exercise.

IMPORTANT: When attaching the lat bar or nylon strap, make sure that the attachments are in the cor-

rect starting position for the exercise to be performed. If there is any slack in the cables or chain as an exercise is performed, the effectiveness of the exercise will be reduced.

CHANGING THE WEIGHT SETTING

To change the weight setting of the weight stack, insert a Weight Pin (26) under the desired Weight

(25). Be sure to insert the Weight Pin until the bent end of the Weight Pin is touching the Weights, and turn the bent end downward. The weight setting of the weight stack can be changed from 6.5 pounds to

106.5 pounds, in increments of 12.5 pounds.Note:

Due to the cables and pulleys, the amount of resistance at each exercise station may vary from the weight setting. Use the WEIGHT RESISTANCE CHART on page 17 to find the approximate

amount of resistance at each weight station.

ATTACHING THE LAT BAR OR NYLON STRAP TO

THE HIGH PULLEY STATION

Attach the Lat Bar (54) to the Long Cable (23) with a Cable Clip (53). For some exercises, the Chain (52) should be attached between the Lat Bar and the Long

Cable with two Cable Clips. Adjust the length of the

Chain between the Lat Bar and the Long Cable so the Lat Bar is in the correct starting position for the exercise to be performed.

The Nylon Strap (39) can be attached in the same manner.

ATTACHING THE LAT BAR OR NYLON STRAP TO

THE LOW PULLEY STATION

Attach the Lat Bar (54) to the Short Cable (58) with a Cable Clip (53). For some exercises, the Chain (52) should be attached between the Lat Bar and the

Pulley Cable with two Cable Clips. Adjust the length of the Chain between the Lat Bar and the Short

Cable so the Lat Bar is in the correct starting position for the exercise to be performed.

The Nylon Strap (39) can be attached in the same manner.

Always remove the leg press plate and lock the leg lever before using the low pulley station (see

ADJUSTING AND REMOVING THE LEG PRESS PLATE AND ADJUSTMENT TUBE and LOCKING THE LEG LEVER on page 17).

25

26

53

23

52

54

39

58

 

 

53

52

54

 

39

16

Image 16
Contents QUESTIONS? Model No. WESY85201 Serial NoCustomer HOT Line Mon.-Fri., 6 a.m.-6 p.m. MSTTable of Contents Limited WarrantyIng down Important PrecautionsMake sure that the cables remain on the pul Using the Weider Before YOU BeginAssembly Assembly, use the Part IdentificationFollowing Tools not Included are Required for Assembly Not tighten the Nylon Locknuts yetEach Carriage Bolt Frame AssemblyTighten all Nylon Locknuts used in steps 1 through Frame Assembly ARM Assembly ShownAttach a V-Pulley 6 and a Long Cable Trap On each Arm. Arm identification is very important for stepAttach the Left Arm 47 in the same manner Nylon Locknuts until the end of this assembly step Tighten all Nylon Locknuts used in this step nowCable Assembly Locate the Long CableA 3/8 Nylon Locknut Cable in placePulley 6 on the Right Arm Be sure 3/8 x 2 1/2 Bolt 7 and the 3/8 Nylon Locknut not shownBracket. Note This may come pre-assem- bled For easy part identificationLocate the Short Cable Route 3/8 x 3 1/2 Bolt 16Front Upright Trap 66 is turned to hold the CableTighten the 3/8 Nylon Locknut 21 and the 3/8 x 3 1/2 Bolt A 1/4 Flat Washer 10. Do not com Cable Assembly Seat AssemblySeat Plate to the Seat 13 with two 1/4 x 1/2 Screws Insert the L-Pin 40 through the holes Seat Assembly Decal Placement8520 Adjustment Changing the Weight SettingAmount of resistance at each weight station Attaching the LAT BAR or Nylon Strap to High Pulley StationWeight Resistance Chart Locking the LEG LeverTROUBLE-SHOOTING and Maintenance Tightening the CablesWoven cable, the type of cable used on the home That the Cable and Pulley move smoothlyCable Diagram Cable traps do not touch or bind the cables Long CableShort Cable Be sure thatOrdering Replacement Parts Part No R1096ARemove this Part Identification Chart from the Manual WESY85201 R1096AParafusode5/16x13/4 Clipe do Cabo Espaçador de 1/2 x 3/4 61-2 Remove this Part LIST/EXPLODED Drawing from the Manual Part LIST-Model No. WESY85201 Qty DescriptionR1096A