Weider WESY85201 user manual Frame Assembly ARM Assembly, Shown

Page 7

FRAME ASSEMBLY

ARM ASSEMBLY

5.Press the Weight Tube Bumper (64) into the end of the Weight Tube (63). Insert the Weight Tube into the stack of Weights (25). Be sure that the pins on the Weight Tube are resting in the pin grooves in the upper Weight.

Lubricate the insides of the holes in the Top Weight (76). Set the Top Weight onto the stack of Weights (25).

Insert both Weight Guides (62) into the stack

of Weights (25). Be sure that the holes in the Weight Guides are at the top, as

shown.

6.Attach the upper ends of the Weight Guides

(62)to the Top Frame (55) with the 5/16” x 6”

Bolt (60), two 1/2” x 3/4” Spacers (61), and a 5/16” Nylon Locknut (3).

Be sure that the Pulley Bracket (20) is in front of the Weight Guide (62) as shown.

7.Press a 1” x 7/8” Plastic Bushing (75) onto each welded spacer on the Press Frame (17).

Slide the Press Frame into place on the Base

(4). Note: This will be a tight fit. The

Plastic Bushings should fit onto each end of the indicated tube in the Base. Be sure that the pulley is on the indicated side.

Lubricate the 3/8” x 8” Bolt (59). Attach the Press Frame (17) to the Base (4) with the

3/8” x 8” Bolt and a 3/8” Nylon Locknut (21).

5

Holes

62

76

Lubricate

63

Pins

64

25

6

61

3

55

60

20

62

7

		Pulley
	17	Lubricate
	17	59
		59

21

Welded

Spacers

4 —Tube	75

7

Image 7

Contents Mon.-Fri., 6 a.m.-6 p.m. MST QUESTIONS?Model No. WESY85201 Serial No Customer HOT LineLimited Warranty Table of ContentsIng down Important PrecautionsMake sure that the cables remain on the pul Before YOU Begin Using the WeiderNot tighten the Nylon Locknuts yet AssemblyAssembly, use the Part Identification Following Tools not Included are Required for AssemblyEach Carriage Bolt Frame AssemblyTighten all Nylon Locknuts used in steps 1 through Shown Frame Assembly ARM AssemblyAttach a V-Pulley 6 and a Long Cable Trap On each Arm. Arm identification is very important for stepAttach the Left Arm 47 in the same manner Tighten all Nylon Locknuts used in this step now Nylon Locknuts until the end of this assembly stepCable in place Cable AssemblyLocate the Long Cable A 3/8 Nylon LocknutFor easy part identification Pulley 6 on the Right Arm Be sure3/8 x 2 1/2 Bolt 7 and the 3/8 Nylon Locknut not shown Bracket. Note This may come pre-assem- bledTrap 66 is turned to hold the Cable Locate the Short Cable Route3/8 x 3 1/2 Bolt 16 Front UprightTighten the 3/8 Nylon Locknut 21 and the 3/8 x 3 1/2 Bolt A 1/4 Flat Washer 10. Do not com Cable Assembly Seat AssemblySeat Plate to the Seat 13 with two 1/4 x 1/2 Screws Insert the L-Pin 40 through the holes Seat Assembly Decal Placement8520 Attaching the LAT BAR or Nylon Strap to High Pulley Station AdjustmentChanging the Weight Setting Amount of resistance at each weight stationLocking the LEG Lever Weight Resistance ChartThat the Cable and Pulley move smoothly TROUBLE-SHOOTING and MaintenanceTightening the Cables Woven cable, the type of cable used on the homeBe sure that Cable DiagramCable traps do not touch or bind the cables Long Cable Short CablePart No R1096A Ordering Replacement PartsWESY85201 R1096A Remove this Part Identification Chart from the ManualParafusode5/16x13/4 Clipe do Cabo Espaçador de 1/2 x 3/4 61-2 Remove this Part LIST/EXPLODED Drawing from the Manual Qty Description Part LIST-Model No. WESY85201R1096A