Weider WESY85201 user manual Seat Assembly Decal Placement, Insert the L-Pin 40 through the holes

Page 15

SEAT ASSEMBLY

DECAL PLACEMENT

32.Press a 1 3/4” Square Inner Cap (44) into the Press Adjustment Tube (79).

Align one set of holes in the Press Adjustment Tube (79) with the holes in the Rocker Arm

(32). Insert the “L”-Pin (40) through the holes.

Be sure that the Press Adjustment Tube is oriented as shown.

Attach the Press Plate (78) to the Press Adjustment Tube (79) with a 5/16” x 2 1/2” Bolt (22), two 5/16” Flat Washers (8), and a 5/16” Nylon Locknut (3).

33.Press a 3/4” Round Inner Cap (34) into each end of the Short Pad Tube (28). Press a 3/4” Round Inner Cap into each end of the Long

Pad Tube (80).

Insert the Short Pad Tube (28) into the Seat

Frame (36). Slide a 5 1/2” Pad (30) onto each end of the Short Pad Tube.

Insert the Long Pad Tube (80) into the Leg

Lever (29). Slide a 5 1/2” Pad (30) onto each end of the Long Pad Tube.

34.Remove the backing from the 8520 decal and apply it to the home gym system as shown.

Make sure that all parts have been properly tightened. The use of the remaining parts will be explained in ADJUSTMENT, beginning on page 16 of this manual.

Before using the home gym system, pull each cable a few times to be sure that the cables move smoothly over the pulleys. If one of the cables does not move smoothly, find and cor-

rect the problem. IMPORTANT: If the cables are not properly installed, they may be damaged when heavy weight is used. See the CABLE DIAGRAM on page 19 of this

manual for proper cable routing. If there is any slack in the cables, you will need to remove it by tightening the cables. See

TROUBLE-SHOOTING AND MAINTE- NANCE on page 18.

32 44

79

8 3

8

22

40

32 78

Slant must be turned this way

33

34

30

28

	36	80	30
		80

			34
30			29
30

34

8520

15

Image 15

Contents Mon.-Fri., 6 a.m.-6 p.m. MST QUESTIONS?Model No. WESY85201 Serial No Customer HOT LineLimited Warranty Table of ContentsImportant Precautions Ing downMake sure that the cables remain on the pul Before YOU Begin Using the WeiderNot tighten the Nylon Locknuts yet AssemblyAssembly, use the Part Identification Following Tools not Included are Required for AssemblyFrame Assembly Each Carriage BoltTighten all Nylon Locknuts used in steps 1 through Shown Frame Assembly ARM AssemblyOn each Arm. Arm identification is very important for step Attach a V-Pulley 6 and a Long Cable TrapAttach the Left Arm 47 in the same manner Tighten all Nylon Locknuts used in this step now Nylon Locknuts until the end of this assembly stepCable in place Cable AssemblyLocate the Long Cable A 3/8 Nylon LocknutFor easy part identification Pulley 6 on the Right Arm Be sure3/8 x 2 1/2 Bolt 7 and the 3/8 Nylon Locknut not shown Bracket. Note This may come pre-assem- bledTrap 66 is turned to hold the Cable Locate the Short Cable Route3/8 x 3 1/2 Bolt 16 Front UprightTighten the 3/8 Nylon Locknut 21 and the 3/8 x 3 1/2 Bolt Cable Assembly Seat Assembly A 1/4 Flat Washer 10. Do not comSeat Plate to the Seat 13 with two 1/4 x 1/2 Screws Seat Assembly Decal Placement Insert the L-Pin 40 through the holes8520 Attaching the LAT BAR or Nylon Strap to High Pulley Station AdjustmentChanging the Weight Setting Amount of resistance at each weight stationLocking the LEG Lever Weight Resistance ChartThat the Cable and Pulley move smoothly TROUBLE-SHOOTING and MaintenanceTightening the Cables Woven cable, the type of cable used on the homeBe sure that Cable DiagramCable traps do not touch or bind the cables Long Cable Short CablePart No R1096A Ordering Replacement PartsWESY85201 R1096A Remove this Part Identification Chart from the ManualParafusode5/16x13/4 Clipe do Cabo Espaçador de 1/2 x 3/4 61-2 Remove this Part LIST/EXPLODED Drawing from the Manual Qty Description Part LIST-Model No. WESY85201R1096A