Weider WESY85201 user manual TROUBLE-SHOOTING and Maintenance, Tightening the Cables

Page 18

TROUBLE-SHOOTING AND MAINTENANCE

Inspect and tighten all parts each time you use the home gym system. Replace any worn parts immediately. The home gym system can be cleaned using a damp cloth and mild non-abrasive detergent. Do not use solvents.

TIGHTENING THE CABLES

Woven cable, the type of cable used on the home

gym system, can stretch slightly when it is first used. If there is slack in the cables before resistance is felt, the cables should be tightened. Slack can be

removed from the cables by tightening the 1/4” Nylon Locknuts (2) at the end of the Long Cable (23) (see drawing 1) and at the end of the Short Cable (58) (see drawing 2). To do this you may need to remove the Small “U”-Bracket (67) from the Weight Tube (not shown) or remove the 3 1/2” Pulley (15) from the Long “U”-Bracket (57). Make sure that the cables are not too tight or the Top Weight (76) will be lifted off the weight stack.

Additional slack can be removed by moving the 3 1/2” Pulley (15) to the other hole in the Long “U”-Bracket (57). Remove the 3/8” Nylon Locknut (21) and the 3/8” x 2” Bolt (12) from the Cable Trap (66), Pulley, and “U”-Bracket. Re-attach the Pulley and Cable Trap. Be sure that the Cable trap is in the proper position

and that the Cable and Pulley move smoothly.

Note: If a cable tends to slip off the pulleys often, the cable may have become twisted. Remove the cable and re-install it.

If the cables need to be replaced, see ORDERING REPLACEMENT PARTS on the back cover of this manual.

1
	23
67
76
	2
2
23	15
	15
66	57
	57
21	12
21
2	58

18

Image 18

Contents Customer HOT Line QUESTIONS?Model No. WESY85201 Serial No Mon.-Fri., 6 a.m.-6 p.m. MSTTable of Contents Limited WarrantyImportant Precautions Ing downMake sure that the cables remain on the pul Using the Weider Before YOU BeginFollowing Tools not Included are Required for Assembly AssemblyAssembly, use the Part Identification Not tighten the Nylon Locknuts yetFrame Assembly Each Carriage BoltTighten all Nylon Locknuts used in steps 1 through Frame Assembly ARM Assembly ShownOn each Arm. Arm identification is very important for step Attach a V-Pulley 6 and a Long Cable TrapAttach the Left Arm 47 in the same manner Nylon Locknuts until the end of this assembly step Tighten all Nylon Locknuts used in this step nowA 3/8 Nylon Locknut Cable AssemblyLocate the Long Cable Cable in placeBracket. Note This may come pre-assem- bled Pulley 6 on the Right Arm Be sure3/8 x 2 1/2 Bolt 7 and the 3/8 Nylon Locknut not shown For easy part identificationFront Upright Locate the Short Cable Route3/8 x 3 1/2 Bolt 16 Trap 66 is turned to hold the CableTighten the 3/8 Nylon Locknut 21 and the 3/8 x 3 1/2 Bolt Cable Assembly Seat Assembly A 1/4 Flat Washer 10. Do not comSeat Plate to the Seat 13 with two 1/4 x 1/2 Screws Seat Assembly Decal Placement Insert the L-Pin 40 through the holes8520 Amount of resistance at each weight station AdjustmentChanging the Weight Setting Attaching the LAT BAR or Nylon Strap to High Pulley StationWeight Resistance Chart Locking the LEG LeverWoven cable, the type of cable used on the home TROUBLE-SHOOTING and MaintenanceTightening the Cables That the Cable and Pulley move smoothlyShort Cable Cable DiagramCable traps do not touch or bind the cables Long Cable Be sure thatOrdering Replacement Parts Part No R1096ARemove this Part Identification Chart from the Manual WESY85201 R1096AParafusode5/16x13/4 Clipe do Cabo Espaçador de 1/2 x 3/4 61-2 Remove this Part LIST/EXPLODED Drawing from the Manual Part LIST-Model No. WESY85201 Qty DescriptionR1096A