Weider WESY85201 user manual Tighten the 3/8 Nylon Locknut 21 and the 3/8 x 3 1/2 Bolt

Page 13

CABLE ASSEMBLY

26.Note: The 3 1/2” Pulley (15) labeled in this step is pre-attached. It is shown removed

for easy part identification.

Route the Short Cable (58) around the 3 1/2” Pulley (15) attached to the upper hole in the

Press Frame (17). Be sure that the Cable is routed around the Pulley as shown.

Tighten the 3/8” Nylon Locknut (21) and the 3/8” x 3 1/2” Bolt (16).

27.Note: The 3 1/2” Pulley (15) labeled in this step is pre-attached. It is shown removed

for easy part identification.

Route the Short Cable (58) around the 3 1/2”

Pulley (15) attached to the upper hole in the

Front Upright (42).	Be sure that the Cable
Trap (66) is turned to hold the Cable in
place and that the Cable is routed around
the Pulley as shown.	Tighten the 3/8” Nylon

Locknut (21) and the 3/8” x 3 3/4” Bolt (71).

28. Attach the end of the Short Cable (58) to the

Long “U”-Bracket (57) with a 1/4” Nylon Lock-

nut (2) and a 1/4” Flat Washer (10). Do not completely tighten the Nylon Locknut. It should be threaded onto the end of the

Cable so only a couple of threads are showing above the nut, as shown in the inset drawing.

26

16

9

17

	58
	15
21	66

27

42

58

15	21

9

66

71

28

2

57

10

58

2

10

57

58

13

Image 13

Contents Model No. WESY85201 Serial No QUESTIONS?Customer HOT Line Mon.-Fri., 6 a.m.-6 p.m. MSTLimited Warranty Table of ContentsIng down Important PrecautionsMake sure that the cables remain on the pul Before YOU Begin Using the WeiderAssembly, use the Part Identification AssemblyFollowing Tools not Included are Required for Assembly Not tighten the Nylon Locknuts yetEach Carriage Bolt Frame AssemblyTighten all Nylon Locknuts used in steps 1 through Shown Frame Assembly ARM AssemblyAttach a V-Pulley 6 and a Long Cable Trap On each Arm. Arm identification is very important for stepAttach the Left Arm 47 in the same manner Tighten all Nylon Locknuts used in this step now Nylon Locknuts until the end of this assembly stepLocate the Long Cable Cable AssemblyA 3/8 Nylon Locknut Cable in place3/8 x 2 1/2 Bolt 7 and the 3/8 Nylon Locknut not shown Pulley 6 on the Right Arm Be sureBracket. Note This may come pre-assem- bled For easy part identification3/8 x 3 1/2 Bolt 16 Locate the Short Cable RouteFront Upright Trap 66 is turned to hold the CableTighten the 3/8 Nylon Locknut 21 and the 3/8 x 3 1/2 Bolt A 1/4 Flat Washer 10. Do not com Cable Assembly Seat AssemblySeat Plate to the Seat 13 with two 1/4 x 1/2 Screws Insert the L-Pin 40 through the holes Seat Assembly Decal Placement8520 Changing the Weight Setting AdjustmentAmount of resistance at each weight station Attaching the LAT BAR or Nylon Strap to High Pulley StationLocking the LEG Lever Weight Resistance ChartTightening the Cables TROUBLE-SHOOTING and MaintenanceWoven cable, the type of cable used on the home That the Cable and Pulley move smoothlyCable traps do not touch or bind the cables Long Cable Cable DiagramShort Cable Be sure thatPart No R1096A Ordering Replacement PartsWESY85201 R1096A Remove this Part Identification Chart from the ManualParafusode5/16x13/4 Clipe do Cabo Espaçador de 1/2 x 3/4 61-2 Remove this Part LIST/EXPLODED Drawing from the Manual Qty Description Part LIST-Model No. WESY85201R1096A