Weider WESY85201 Pulley 6 on the Right Arm Be sure, Bracket. Note This may come pre-assem- bled

Page 11

CABLE ASSEMBLY

18. Route the Long Cable (23) around the “V”-

 

 

Pulley (6) on the Right Arm (48).

Be sure

that the Cable is in the groove of the “V”-

 

Pulley and that the Long Cable Trap (50)

is

turned to hold the Cable in place.

 

Tighten

the 3/8” x 2 1/2” Bolt (7) and the 3/8” Nylon Locknut (not shown).

19.Route the Long Cable (23) around the 3 1/2” Pulley (15) attached to the Pulley Bracket

(20). Be sure that the Cable is in the groove of the Pulley and that the Cable Trap (66) is turned to hold the Cable in place. Tighten the 3/8” x 2” Bolt (12) and the 3/8” Nylon Locknut (not shown).

Be sure that the 5/16” x 5” Bolt (68) is proper- ly tightened and that the Pulley Bracket (20) can move freely.

20.See the inset drawing. Attach a 3 1/2” Pulley

(15)and a Cable Trap (66) to the indicated

hole in the Long “U”-Bracket (57) with a 3/8” x

2” Bolt (12) and a 3/8” Nylon Locknut (21). Be sure that the Cable Trap is inside the “U”-

Bracket. Note: This may come pre-assem- bled.

Route the Long Cable (23) around the 3 1/2” Pulley (15) and through the Long “U”-Bracket (57). Be sure that the Cable is in the groove of the Pulley and that the Cable and Pulley move smoothly.

21.Note: The 3 1/2” Pulley (15) labeled in this step is pre-attached. It is shown removed

for easy part identification.

Route the Long Cable (23) around the 3 1/2” Pulley (15) attached to the bracket on the Top Frame (55). Tighten the 3/8” x 2” Bolt (12)

and the 3/8” Nylon Locknut (21). Be sure that

the Cable is in the groove of the Pulley and that the Cable and Pulley move smoothly.

18

50

7

 

 

6

48

23

19

68

66

 

 

20

 

12

 

23

15

 

20

23

23

 

66

15

12

 

21

57

21

23 15

Bracket

12

55

21

11

Image 11
Contents Mon.-Fri., 6 a.m.-6 p.m. MST QUESTIONS?Model No. WESY85201 Serial No Customer HOT LineLimited Warranty Table of ContentsMake sure that the cables remain on the pul Important PrecautionsIng down Before YOU Begin Using the WeiderNot tighten the Nylon Locknuts yet AssemblyAssembly, use the Part Identification Following Tools not Included are Required for AssemblyTighten all Nylon Locknuts used in steps 1 through Frame AssemblyEach Carriage Bolt Shown Frame Assembly ARM AssemblyAttach the Left Arm 47 in the same manner On each Arm. Arm identification is very important for stepAttach a V-Pulley 6 and a Long Cable Trap Tighten all Nylon Locknuts used in this step now Nylon Locknuts until the end of this assembly stepCable in place Cable AssemblyLocate the Long Cable A 3/8 Nylon LocknutFor easy part identification Pulley 6 on the Right Arm Be sure3/8 x 2 1/2 Bolt 7 and the 3/8 Nylon Locknut not shown Bracket. Note This may come pre-assem- bledTrap 66 is turned to hold the Cable Locate the Short Cable Route3/8 x 3 1/2 Bolt 16 Front UprightTighten the 3/8 Nylon Locknut 21 and the 3/8 x 3 1/2 Bolt Seat Plate to the Seat 13 with two 1/4 x 1/2 Screws Cable Assembly Seat AssemblyA 1/4 Flat Washer 10. Do not com 8520 Seat Assembly Decal PlacementInsert the L-Pin 40 through the holes Attaching the LAT BAR or Nylon Strap to High Pulley Station AdjustmentChanging the Weight Setting Amount of resistance at each weight stationLocking the LEG Lever Weight Resistance ChartThat the Cable and Pulley move smoothly TROUBLE-SHOOTING and MaintenanceTightening the Cables Woven cable, the type of cable used on the homeBe sure that Cable DiagramCable traps do not touch or bind the cables Long Cable Short CablePart No R1096A Ordering Replacement PartsWESY85201 R1096A Remove this Part Identification Chart from the ManualParafusode5/16x13/4 Clipe do Cabo Espaçador de 1/2 x 3/4 61-2 Remove this Part LIST/EXPLODED Drawing from the Manual Qty Description Part LIST-Model No. WESY85201R1096A