Weider WESY85201 user manual Nylon Locknuts until the end of this assembly step

Page 9

ARM ASSEMBLY

11.Press a 1 3/4” Square Inner Cap (44) into the Seat Frame (36). Attach a Bumper (73) to the Seat Frame with a 1/2” Tap Screw (65).

Slide the Seat Frame (36) onto the 5/16” x
2 1/2” Carriage Bolts (1) in the Base (4).		See
the inset drawing. The bracket on the Seat
Frame must be behind the Press Frame
(17)Hand. -tighten a 5/16” Nylon Locknut (3)
onto each Carriage Bolt.	Do not tighten the

Nylon Locknuts until the end of this assembly step.

Attach the Seat Frame (36) to the Front

Upright (42) with two 5/16” x 2 3/4” Bolts (11), two 5/16” Flat Washers (8), and two 5/16”

Nylon Locknuts (3).

Tighten all Nylon Locknuts used in this step now.

12.Attach a Bumper (73) to the Rocker Arm (32) with a 1/2” Tap Screw (65).

Lubricate a 3/8” x 3 1/4” Bolt (35). Attach the Rocker arm (32) to the Base (4) with the 3/8”

x 3 1/4” Bolt and a 3/8” Nylon Locknut (21).

13.Lubricate a 3/8” x 2 1/2” Bolt (7). Attach the Leg Lever (29) to the Rocker Arm (32) with

the 3/8” x 2 1/2” Bolt and a 3/8” Nylon Jam Nut (33).

Press a 1 3/4” Square Inner Cap (44) into each end of the Leg Lever (29).

11
	Bracket	36
		36
	17
42
3
8		44
8
11
		73
	36	65
		3
4	1
	1
12
	73
	65
	32
		21
		4
Lubricate—35
13
	44
	32
		7—Lubricate
	33
		29
		44

9

Image 9

Contents Model No. WESY85201 Serial No QUESTIONS?Customer HOT Line Mon.-Fri., 6 a.m.-6 p.m. MSTLimited Warranty Table of ContentsImportant Precautions Ing downMake sure that the cables remain on the pul Before YOU Begin Using the WeiderAssembly, use the Part Identification AssemblyFollowing Tools not Included are Required for Assembly Not tighten the Nylon Locknuts yetFrame Assembly Each Carriage BoltTighten all Nylon Locknuts used in steps 1 through Shown Frame Assembly ARM AssemblyOn each Arm. Arm identification is very important for step Attach a V-Pulley 6 and a Long Cable TrapAttach the Left Arm 47 in the same manner Tighten all Nylon Locknuts used in this step now Nylon Locknuts until the end of this assembly stepLocate the Long Cable Cable AssemblyA 3/8 Nylon Locknut Cable in place3/8 x 2 1/2 Bolt 7 and the 3/8 Nylon Locknut not shown Pulley 6 on the Right Arm Be sureBracket. Note This may come pre-assem- bled For easy part identification3/8 x 3 1/2 Bolt 16 Locate the Short Cable RouteFront Upright Trap 66 is turned to hold the CableTighten the 3/8 Nylon Locknut 21 and the 3/8 x 3 1/2 Bolt Cable Assembly Seat Assembly A 1/4 Flat Washer 10. Do not comSeat Plate to the Seat 13 with two 1/4 x 1/2 Screws Seat Assembly Decal Placement Insert the L-Pin 40 through the holes8520 Changing the Weight Setting AdjustmentAmount of resistance at each weight station Attaching the LAT BAR or Nylon Strap to High Pulley StationLocking the LEG Lever Weight Resistance ChartTightening the Cables TROUBLE-SHOOTING and MaintenanceWoven cable, the type of cable used on the home That the Cable and Pulley move smoothlyCable traps do not touch or bind the cables Long Cable Cable DiagramShort Cable Be sure thatPart No R1096A Ordering Replacement PartsWESY85201 R1096A Remove this Part Identification Chart from the ManualParafusode5/16x13/4 Clipe do Cabo Espaçador de 1/2 x 3/4 61-2 Remove this Part LIST/EXPLODED Drawing from the Manual Qty Description Part LIST-Model No. WESY85201R1096A