Weider WESY85201 user manual Locate the Short Cable Route, 3/8 x 3 1/2 Bolt 16, Front Upright

Page 12


22. Locate the Short Cable (58).		Route the
Short Cable under the 3 1/2” Low Pulley (77).
Be sure that the end of the Cable with the
ball is on the indicated side of the Pulley
and that the Cable is between the Pulley
and the welded spacer on the Leg Lever
(29)Tighten.	the 3/8” x 3 1/2” Bolt (16) and

the 3/8” Nylon Locknut (not shown).

23.Wrap the Short Cable (58) around a “V”- Pulley (6). Attach the Pulley and a Long Cable Trap (50) inside the bracket on the

Seat Frame (36) with a 3/8” x 2 1/2” Bolt (7)

and a 3/8” Nylon Locknut (21). Be sure that

the Cable Trap is turned to hold the Cable in place and that the Cable is routed around the Pulley as shown.

22

29
16
58
77	Ball
Welded Spacer

23

6	58
	21

50

7

36

CABLE ASSEMBLY

24.Wrap the Short Cable (58) around a 3 1/2” Pulley (15). Attach the Pulley to the Rocker

Arm (32) with a 3/8” x 3 1/2” Bolt (16), a 3/8” Flat Washer (9), and a 3/8” Nylon Locknut

(21). Be sure that the Cable Trap (66) is turned to hold the Cable in place and that the Cable is routed around the Pulley as shown.

25. Note: The 3 1/2” Pulley (15) labeled in this

step is pre-attached. It is shown removed

for easy part identification.

24

15

32

21

9

25

42

66

16

58

Route the Short Cable (58) around the 3 1/2” Pulley (15) attached to the lower hole in the

Front Upright (42).	Be sure that the Cable
Trap (66) is turned to hold the Cable in
place and that the Cable is routed around
the Pulley as shown.	Tighten the 3/8” Nylon

Locknut (21) and the 3/8” x 3 3/4” Bolt (71).

	71
15	66
15

21	58
	9

12

Image 12

Contents QUESTIONS? Model No. WESY85201 Serial NoCustomer HOT Line Mon.-Fri., 6 a.m.-6 p.m. MSTTable of Contents Limited WarrantyImportant Precautions Ing downMake sure that the cables remain on the pul Using the Weider Before YOU BeginAssembly Assembly, use the Part IdentificationFollowing Tools not Included are Required for Assembly Not tighten the Nylon Locknuts yetFrame Assembly Each Carriage BoltTighten all Nylon Locknuts used in steps 1 through Frame Assembly ARM Assembly ShownOn each Arm. Arm identification is very important for step Attach a V-Pulley 6 and a Long Cable TrapAttach the Left Arm 47 in the same manner Nylon Locknuts until the end of this assembly step Tighten all Nylon Locknuts used in this step nowCable Assembly Locate the Long CableA 3/8 Nylon Locknut Cable in placePulley 6 on the Right Arm Be sure 3/8 x 2 1/2 Bolt 7 and the 3/8 Nylon Locknut not shownBracket. Note This may come pre-assem- bled For easy part identificationLocate the Short Cable Route 3/8 x 3 1/2 Bolt 16Front Upright Trap 66 is turned to hold the CableTighten the 3/8 Nylon Locknut 21 and the 3/8 x 3 1/2 Bolt Cable Assembly Seat Assembly A 1/4 Flat Washer 10. Do not comSeat Plate to the Seat 13 with two 1/4 x 1/2 Screws Seat Assembly Decal Placement Insert the L-Pin 40 through the holes8520 Adjustment Changing the Weight SettingAmount of resistance at each weight station Attaching the LAT BAR or Nylon Strap to High Pulley StationWeight Resistance Chart Locking the LEG LeverTROUBLE-SHOOTING and Maintenance Tightening the CablesWoven cable, the type of cable used on the home That the Cable and Pulley move smoothlyCable Diagram Cable traps do not touch or bind the cables Long CableShort Cable Be sure thatOrdering Replacement Parts Part No R1096ARemove this Part Identification Chart from the Manual WESY85201 R1096AParafusode5/16x13/4 Clipe do Cabo Espaçador de 1/2 x 3/4 61-2 Remove this Part LIST/EXPLODED Drawing from the Manual Part LIST-Model No. WESY85201 Qty DescriptionR1096A