Turning off the sounds temporarily
From the remote control ONLY:
Press MUTING to turn off the sound through all connected speakers and headphones.
“MUTING” appears on the display and the volume turns off.
EQ C.TONE | VIRTUAL SB AUDIO P. BASS | TA NEWS INFO RDS TUNED ST AUTO MUTING SLEEP AUTO MODE | ||||||
LPCM | L | C | R |
| PL | ATT | ||
DOLBY D | S . WFR LFE | NEO : 6 | HP | |||||
DTS AAC |
|
|
|
|
| DSP 3D | MHz | |
LS | SB | RS | ||||||
96 / 24 | AUTO SR | kHz | ||||||
|
|
|
|
|
|
|
| |
To restore the sound, press MUTING again.
•Pressing VOLUME +/– (or turning MASTER VOLUME control on the front panel) also restores the sound.
Changing the display brightness
You can dim the
From the remote control ONLY:
Press DIMMER repeatedly.
•Each time you press the button, the display brightness changes as follows:
DIMMER 1: Dims the display slightly.
Dims the blue illumination slightly.
DIMMER 2: Dims the display more than DIMMER 1. Dims the blue illumination slightly (more than DIMMER 1).
DIMMER 3: Turns off the display and blue illumination. (Temporarily canceled when you operate the receiver.*)
DIMMER OFF: Cancels the Dimmer (normal display).
* Except when activating or deactivating TV Direct.
Turning off the power with the Sleep Timer
You can fall asleep while listening to
From the remote control ONLY:
Press SLEEP repeatedly.
•Each time you press the button, the
|
|
|
|
|
|
| SLEEP indicator | ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||
EQ C.TONE | VIRTUAL SB AUDIO P. BASS | TA NEWS INFO RDS TUNED ST AUTO MUTING SLEEP AUTO MODE |
| ||||||
LPCM | L | C | R |
| PL |
| ATT |
| |
DOLBY D | S . WFR LFE | NEO : 6 |
| HP |
| ||||
DTS AAC |
|
|
|
|
| DSP 3D |
| MHz |
|
LS | SB | RS |
| ||||||
96 / 24 | AUTO SR |
| kHz |
| |||||
|
|
|
|
|
|
|
|
|
|
10
20 
30 
40 
50 
60
OFF (canceled)
90 
80 
70 
When the
The receiver turns off automatically.
To check or change the remaining time until the
Press SLEEP once.
The remaining time (in minutes) until the
• To change the
To cancel the Sleep Timer:
Press SLEEP repeatedly so that “SLEEP OFF” appears on the display. (The SLEEP indicator goes off.)
•The Sleep Timer is also canceled when:
–You turn off the receiver, or
–TV Direct is activated.
Basic adjustment of auto memory
This receiver memorizes sound settings for each source:
•when you turn off the power, and
•when you change the source.
When you change the source, the memorized settings for the newly selected source are automatically recalled.
The following can be stored for each source:
•Analogue/digital input mode (see page 12)
•Subwoofer audio position (see page 14)
•Midnight mode (see page 23)
•Speaker output level (see page 29)
•Digital equalization pattern (see page 30)
•Bass boost (see page 30)
•Subwoofer phase (see page 30)
•Input attenuator mode (see page 30)
•Surround/DSP mode selection (see pages 41 to 43)
NOTE
If the source is “FM” or “AM,” you can assign a different setting for each band.
Signal and speaker indicators on the display
Signal indicatorsSpeaker indicators
| L |
| C R |
|
|
|
|
|
|
|
|
|
|
|
| L |
|
| C |
| R | ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
S . WFR LFE |
| EQ C.TONE | VIRTUAL SB AUDIO P. BASS | TA NEWS | INFO RDS | ||||||||||||||||||||
| LPCM |
| L |
| C R | PL | S . WFR LFE | ||||||||||||||||||
|
|
|
|
|
|
| DOLBY D |
|
|
|
|
|
| NEO : 6 |
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
| S . | WFR | LFE |
|
|
|
|
|
|
|
|
| |||||||
LS | SB RS |
| LS SB | RS | |||||||||||||||||||||
| DTS | AAC |
|
|
|
|
|
|
| DSP 3D | |||||||||||||||
| LS SB RS | ||||||||||||||||||||||||
| 96 / | 24 | AUTO SR | ||||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
The signal indicators light up as follows:
L:• When digital input is selected: Lights up when the
left channel signal comes in.
•When analogue input is selected: Always lights up.
R:• When digital input is selected: Lights up when the right channel signal comes in.
•When analogue input is selected: Always lights up.
C:Lights up when the center channel signal comes in. LS*: Lights up when the left surround channel signal comes
in.
RS*: Lights up when the right surround channel signal comes in.
SB: Lights up when the surround back channel signal comes in.
LFE: Lights up when the LFE channel signal comes in.
* When monaural surround signal comes in, only “S” lights up.
NOTE
When “DVD MULTI” is selected as the source, all the signal indicators except “SB” light up.
The speaker indicators light up as follows:
•The subwoofer indicator (S . WFR) lights up when “SUBWOOFER” is set to “SUBWOOFER: YES.” For details, see page 21.
•The other speaker indicators light up only when the corresponding speaker is set to “SMALL” or “LARGE,” and also when required for the current playback.
15