JVC LVT1306-007A manual Above ALL

Page 4

SAFETY INSTRUCTIONS

“SOME DOS AND DON’TS ON THE SAFE USE OF EQUIPMENT”

This equipment has been designed and manufactured to meet international safety standards but, like any electrical equipment, care must be taken if you are to obtain the best results and safety is to be assured.

Do read the operating instructions before you attempt to use the equipment.

Do ensure that all electrical connections (including the mains plug, extension leads and interconnections between pieces of equipment) are properly made and in accordance with the manufacturer’s instructions. Switch off and withdraw the mains plug when making or changing connections.

Do consult your dealer if you are ever in doubt about the installation, operation or safety of your equipment.

Do be careful with glass panels or doors on equipment.

DON’T continue to operate the equipment if you are in any doubt about it working normally, or if it is damaged in any way—switch off, withdraw the mains plug and consult your dealer.

DON’T remove any fixed cover as this may expose dangerous voltages.

DON’T leave equipment switched on when it is unattended unless it is specifically stated that it is designed for unattended operation or has a standby mode.

Switch off using the switch on the equipment and make sure that your family know how to do this.

Special arrangements may need to be made for infirm or handicapped people.

DON’T use equipment such as personal stereos or radios so that you are distracted from the requirements of traffic safety. It is illegal to watch television whilst driving.

DON’T listen to headphones at high volume as such use can permanently damage your hearing.

DON’T obstruct the ventilation of the equipment, for example with curtains or soft furnishings.

Overheating will cause damage and shorten the life of the equipment.

DON’T use makeshift stands and NEVER fix legs with wood screws—to ensure complete safety always fit the manufacturer’s approved stand or legs with the fixings provided according to the instructions.

DON’T allow electrical equipment to be exposed to rain or moisture.

ABOVE ALL

NEVER let anyone, especially children, push anything into holes, slots or any other opening in the case—this could result in a fatal electrical shock.;

NEVER guess or take chances with electrical equipment of any kind—it is better to be safe than sorry!

G-3

Image 4
Contents RX-F31S LVT1306-007AImportant for the U.K If in Doubt Consult a Competent ElectricianRX-F31S Above ALL Table of Contents TUNING, Tuning 9, MEMORY, FM Mode Remote controlParts identification Display window Front panelRear panel Before Installation Putting batteries in the remote controlChecking the supplied accessories Getting startedConnecting the FM and AM MW antennas FM antenna connectionConnecting the speakers Speaker Layout DiagramConnecting the speakers Connecting the powered subwooferScart Terminal Specifications Connecting video componentsScart connection For an analogue decoder Audio/video connectionFor T-V Link About DVD Multi Connecting another video component to the Video in jacks Connecting the power cord Digital connectionTurn on the power Selecting the analogue or digital input modeTo turn off the power into standby Basic operationsSelecting the digital decode mode Adjust the volumeListening with headphones Adjusting the subwoofer audio position OFF canceledActivating TV Direct Press TV DirectTurning off the power with the Sleep Timer Basic adjustment of auto memorySignal and speaker indicators on the display Turning off the sounds temporarilyFrom the remote control only Basic settingsTake your position where you listen to the sound RS LS Basic setting items Operation through on-screen display menusMenu operation buttons On the front panelSetup menu configuration Menu operating procedure To select Setting MENU, press SETButton indications on the screen To select the desired submenu, press 5 or ∞ repeatedlySetting the items Setting the speakersSetting subwoofer information-SUBWOOFER Press SETSetting the speaker distance Setting the virtual surround back speakerSelecting the main or sub channel Setting bass sound Using the Midnight modeSetting the low frequency effect attenuator Setting the crossover frequency-CROSSOVERSetting the Auto Function mode Auto Mode AUTO1Auto Mode AUTO2 Auto Mode ManualSelecting the type of the input signal Superimposing the menusSound adjustments Basic adjustment itemsTOP Menu To select Adjust MENU, press SET 10 0 +10Adjusting speaker output level Adjusting the itemsLS RS Adjusting the bass sounds Selecting the subwoofer sound phaseAttenuating the input signal-INPUT ATT Reinforcing the bass-BASS BoostAdjusting the effect level for DSP modes Adjusting the sound parameters for the Surround/DSP modesMaking the center tone soft or sharp Tuning in to stations manually Using preset tuningTo store the preset stations Tuner operationsSelecting the FM reception mode To tune in a preset stationFrom the remote control Press FM/AM to select the band Press Tuner PresetUsing the Radio Data System RDS to receive FM stations What information can RDS signals provide?Press Display while listening to an FM station Frequency RT Normal indicationTo search for a program using the PTY codes Searching for a program by PTY codesPTY codes Press PTY Search while listening to an FM stationDescription of the PTY codes TestNews News Canceled TA/NEWS/INFO NEWS/INFODisplay Creating realistic sound fields Reproducing theatre ambienceIntroducing the Surround modes Dolby Digital3D Headphone mode About other digital signalsDolby Surround DTSIntroducing the DSP modes Digital Acoustic Processor DAP modesHALL1 HALL2This mode cannot be used for multi-channel digital signals All Channel Stereo mode ALL CH STActivating the Surround/DSP modes Turn Multi JOG to select the Surround/DSP mode you want To cancel Surround/DSP modesSelect and play any source other than DVD Multi Surround modesHow does Auto Surr work? Operating other JVC products DVD recorder or DVD playerVCR Channel +Changing the remote control code for DVD recorder Release DVR/DVDDVR/DVD TOP MENU/MENUChanging the transmittable signals for operating a TV Operating other manufacturers’ productsRelease TV Try to operate your TV by pressing TVChanging the transmittable signals for operating a VCR Release VCRTry to operate your VCR by pressing VCR Manufacturers’ codes for VCRChanging the transmittable signals for operating an STB Release STBTry to operate your STB by pressing STB Manufacturers’ codes for STBPower Sound and picture Remote control Tuner TroubleshootingProblem Possible Cause Solution Specifications AmplifierFM tuner IHF AM MW tuner0405RYMMDWJEIN