JVC LVT1306-007A manual Changing the transmittable signals for operating a VCR, Release VCR, Vcr

Page 51

❏Changing the transmittable signals for operating a VCR

Set the mode selector to “AUDIO/TV/VCR/STB.”

1Press and hold VCR .

2Press VCR.

3Enter the manufacturer’s code using buttons 1 – 9, and 0.

See “Manufacturers’ codes for VCR” on the right.

4Release VCR .

Now, you can perform the following operation on the VCR.

VCR : Turn on or off the VCR.

After pressing VCR, you can perform the following operations on the VCR.

CHANNEL +/–:	Change the channel numbers on the
	VCR.

1 – 9, 0:	Select the channel numbers on the VCR.

3:	Start playback.

7:	Stop playback.

8:	Pause playback.

¡:	Fast-wind a tape.

1:	Rewind a tape.

See the instructions supplied with the VCR for details.

5Try to operate your VCR by pressing VCR .

When your VCR turns on or off, you have entered the correct

code.

If more than one code is listed for your brand of VCR, try each

one until the correct one is entered.

Manufacturers’ codes for VCR

Manufacturer		Codes

JVC	01, 02
Akai	02, 37
Bell+Howell	04, 17
Blaupunkt	05
CGM	04, 06, 17
Daewoo	35
Digtal	06
Fisher	04, 17
G.E.	07
Grundig	08
Hitachi	09, 10
Loewe	06, 11, 12
Magnavox	05, 06
Mitsubishi	13	– 16
Nokia	17
Nordmende	18	– 20, 32
Orion	21
Panasonic	22
Philips	06, 23
Phonola	06
Saba	18	– 20, 24, 32
Samsung	25, 26
Sanyo	04, 17
Sharp	27, 28
Siemens	08
Sony	29	– 31, 36
Telefunken	18	– 20, 32, 33
Toshiba	34

Initial setting: 01

Manufacturers’ codes are subject to change without notice. If they are changed, this remote control cannot operate the equipment.

47

Image 51

Contents LVT1306-007A RX-F31SIf in Doubt Consult a Competent Electrician Important for the U.KRX-F31S Above ALL Table of Contents Remote control TUNING, Tuning 9, MEMORY, FM ModeParts identification Front panel Display windowRear panel Getting started Before InstallationPutting batteries in the remote control Checking the supplied accessoriesFM antenna connection Connecting the FM and AM MW antennasConnecting the powered subwoofer Connecting the speakersSpeaker Layout Diagram Connecting the speakersConnecting video components Scart Terminal SpecificationsScart connection Audio/video connection For an analogue decoderFor T-V Link About DVD Multi Connecting another video component to the Video in jacks Digital connection Connecting the power cordBasic operations Turn on the powerSelecting the analogue or digital input mode To turn off the power into standbyAdjust the volume Selecting the digital decode modeListening with headphones Press TV Direct Adjusting the subwoofer audio positionOFF canceled Activating TV DirectTurning off the sounds temporarily Turning off the power with the Sleep TimerBasic adjustment of auto memory Signal and speaker indicators on the displayBasic settings From the remote control onlyTake your position where you listen to the sound RS LS On the front panel Basic setting itemsOperation through on-screen display menus Menu operation buttonsSetup menu configuration To select the desired submenu, press 5 or ∞ repeatedly Menu operating procedureTo select Setting MENU, press SET Button indications on the screenPress SET Setting the itemsSetting the speakers Setting subwoofer information-SUBWOOFERSetting the virtual surround back speaker Setting the speaker distanceSelecting the main or sub channel Setting the crossover frequency-CROSSOVER Setting bass soundUsing the Midnight mode Setting the low frequency effect attenuatorAuto Mode Manual Setting the Auto Function modeAuto Mode AUTO1 Auto Mode AUTO2Superimposing the menus Selecting the type of the input signalBasic adjustment items Sound adjustmentsTOP Menu 10 0 +10 To select Adjust MENU, press SETAdjusting the items Adjusting speaker output levelLS RS Reinforcing the bass-BASS Boost Adjusting the bass soundsSelecting the subwoofer sound phase Attenuating the input signal-INPUT ATTAdjusting the sound parameters for the Surround/DSP modes Adjusting the effect level for DSP modesMaking the center tone soft or sharp Tuner operations Tuning in to stations manuallyUsing preset tuning To store the preset stationsPress Tuner Preset Selecting the FM reception modeTo tune in a preset station From the remote control Press FM/AM to select the bandFrequency RT Normal indication Using the Radio Data System RDS to receive FM stationsWhat information can RDS signals provide? Press Display while listening to an FM stationPress PTY Search while listening to an FM station To search for a program using the PTY codesSearching for a program by PTY codes PTY codesTest Description of the PTY codesCanceled TA/NEWS/INFO NEWS/INFO News NewsDisplay Dolby Digital Creating realistic sound fieldsReproducing theatre ambience Introducing the Surround modesDTS 3D Headphone modeAbout other digital signals Dolby SurroundHALL2 Introducing the DSP modesDigital Acoustic Processor DAP modes HALL1All Channel Stereo mode ALL CH ST This mode cannot be used for multi-channel digital signalsActivating the Surround/DSP modes Surround modes Turn Multi JOG to select the Surround/DSP mode you wantTo cancel Surround/DSP modes Select and play any source other than DVD MultiHow does Auto Surr work? Channel + Operating other JVC productsDVD recorder or DVD player VCRTOP MENU/MENU Changing the remote control code for DVD recorderRelease DVR/DVD DVR/DVDTry to operate your TV by pressing TV Changing the transmittable signals for operating a TVOperating other manufacturers’ products Release TVManufacturers’ codes for VCR Changing the transmittable signals for operating a VCRRelease VCR Try to operate your VCR by pressing VCRManufacturers’ codes for STB Changing the transmittable signals for operating an STBRelease STB Try to operate your STB by pressing STBTroubleshooting Power Sound and picture Remote control TunerProblem Possible Cause Solution AM MW tuner SpecificationsAmplifier FM tuner IHF0405RYMMDWJEIN