JVC LVT1306-007A manual To select Adjust MENU, press SET, 10 0 +10

Page 32

Menu operating procedure

When operating, the on-screen display appears on the TV screen regardless of the SUPERIMPOSE setting (see page 25).

Before you start, remember...

There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again. In this section, the operation of the remote control is used for explaining.

Ex.: When adjusting subwoofer output level.

Operations

 

On the TV screen

 

On the display

 

 

 

 

 

1 To show “TOP MENU,” press MENU.

 

 

 

 

 

 

x

ATT

 

TOP MENU

 

O P. BASS TA NEWS INFO RDS TUNED ST AUTO MUTING SLEEP AUTO MODE

Then press 5 or ∞ to select “ADJUST

 

 

HP

5

 

 

kHz

 

 

 

 

MHz

MENU.”

SETTING MENU

 

 

 

“SETTING” appears.

 

ADJUST MENU

 

 

 

∞

• On the front panel, turn MULTI JOG.

:ENTER :EXIT

“TOP MENU” appears.

2To select “ADJUST MENU,” press SET.

 

O P. BASS TA NEWS INFO RDS TUNED ST AUTO MUTING SLEEP AUTO MODE

ADJUST MENU (1)

x

ATT

 

HP

5

 

MHz

 

kHz

SUBWOOFER LEVEL

:

0

 

 

The submenu previously

FRONT L LEVEL

:

0

 

FRONT R LEVEL

:

0

 

selected appears.

CENTER LEVEL

:

0

 

 

SURR. L LEVEL

:

0

 

 

SURR. R LEVEL

:

0

 

 

∞

:ENTER :TOP MENU

The adjustment item previously selected

appears.

3To select the desired submenu, press 5 or ∞ repeatedly.

There are three screens from “ADJUST MENU (1)” to “ADJUST MENU (3).” To change the screen, simply pressing 5 or ∞ repeatedly. You can go to the next/previous screen.

• On the front panel, turn MULTI JOG.

4Press SET.

SUBWOOFER LEVEL

SUBWOOFER

:2 0 3

O P. BASS

TA NEWS INFO RDS TUNED ST AUTO MUTING SLEEP AUTO MODE

x

ATT

 

HP

 

MHz

 

kHz

 

 

The current setting of the

selected item appears.

23:OPERATE :BACK

The selected submenu appears.

5To adjust the selected item, press 2 or 3 repeatedly, then press SET.

The on-screen display returns to the previous ADJUST MENU. In this example, “ADJUST MENU (1)” appears on the TV screen and “SUBWFR LVL” appears on the display.

•On the front panel, turn MULTI JOG, then press SET.

 

 

 

 

O P. BASS TA NEWS INFO RDS TUNED ST AUTO MUTING SLEEP AUTO MODE

SUBWOOFER LEVEL

 

 

x

HP

 

 

 

 

ATT

 

 

 

 

 

MHz

 

 

 

 

 

kHz

SUBWOOFER

:2

0 3

 

 

 

 

 

–10 0+10

6Repeat steps 2 to 5 to set other items if necessary.

28

Page 31 Page 33
Image 32
Page 31 Page 33
Contents RX-F31S LVT1306-007AImportant for the U.K If in Doubt Consult a Competent ElectricianRX-F31S Above ALL Table of Contents Parts identification Remote controlTUNING, Tuning 9, MEMORY, FM Mode Rear panel Front panelDisplay window Before Installation Putting batteries in the remote controlChecking the supplied accessories Getting startedConnecting the FM and AM MW antennas FM antenna connectionConnecting the speakers Speaker Layout DiagramConnecting the speakers Connecting the powered subwooferScart connection Connecting video componentsScart Terminal Specifications For T-V Link Audio/video connectionFor an analogue decoder About DVD Multi Connecting another video component to the Video in jacks Connecting the power cord Digital connectionTurn on the power Selecting the analogue or digital input modeTo turn off the power into standby Basic operationsListening with headphones Adjust the volumeSelecting the digital decode mode Adjusting the subwoofer audio position OFF canceledActivating TV Direct Press TV DirectTurning off the power with the Sleep Timer Basic adjustment of auto memorySignal and speaker indicators on the display Turning off the sounds temporarilyTake your position where you listen to the sound Basic settingsFrom the remote control only RS LS Basic setting items Operation through on-screen display menusMenu operation buttons On the front panelSetup menu configuration Menu operating procedure To select Setting MENU, press SETButton indications on the screen To select the desired submenu, press 5 or ∞ repeatedlySetting the items Setting the speakersSetting subwoofer information-SUBWOOFER Press SETSelecting the main or sub channel Setting the virtual surround back speakerSetting the speaker distance Setting bass sound Using the Midnight modeSetting the low frequency effect attenuator Setting the crossover frequency-CROSSOVERSetting the Auto Function mode Auto Mode AUTO1Auto Mode AUTO2 Auto Mode ManualSelecting the type of the input signal Superimposing the menusSound adjustments Basic adjustment itemsTOP Menu To select Adjust MENU, press SET 10 0 +10LS RS Adjusting the itemsAdjusting speaker output level Adjusting the bass sounds Selecting the subwoofer sound phaseAttenuating the input signal-INPUT ATT Reinforcing the bass-BASS BoostMaking the center tone soft or sharp Adjusting the sound parameters for the Surround/DSP modesAdjusting the effect level for DSP modes Tuning in to stations manually Using preset tuningTo store the preset stations Tuner operationsSelecting the FM reception mode To tune in a preset stationFrom the remote control Press FM/AM to select the band Press Tuner PresetUsing the Radio Data System RDS to receive FM stations What information can RDS signals provide?Press Display while listening to an FM station Frequency RT Normal indicationTo search for a program using the PTY codes Searching for a program by PTY codesPTY codes Press PTY Search while listening to an FM stationDescription of the PTY codes TestDisplay Canceled TA/NEWS/INFO NEWS/INFONews News Creating realistic sound fields Reproducing theatre ambienceIntroducing the Surround modes Dolby Digital3D Headphone mode About other digital signalsDolby Surround DTSIntroducing the DSP modes Digital Acoustic Processor DAP modesHALL1 HALL2Activating the Surround/DSP modes All Channel Stereo mode ALL CH STThis mode cannot be used for multi-channel digital signals Turn Multi JOG to select the Surround/DSP mode you want To cancel Surround/DSP modesSelect and play any source other than DVD Multi Surround modesHow does Auto Surr work? Operating other JVC products DVD recorder or DVD playerVCR Channel +Changing the remote control code for DVD recorder Release DVR/DVDDVR/DVD TOP MENU/MENUChanging the transmittable signals for operating a TV Operating other manufacturers’ productsRelease TV Try to operate your TV by pressing TVChanging the transmittable signals for operating a VCR Release VCRTry to operate your VCR by pressing VCR Manufacturers’ codes for VCRChanging the transmittable signals for operating an STB Release STBTry to operate your STB by pressing STB Manufacturers’ codes for STBProblem Possible Cause Solution TroubleshootingPower Sound and picture Remote control Tuner Specifications AmplifierFM tuner IHF AM MW tuner0405RYMMDWJEIN
Top Page Image Contents