JVC LVT1306-007A manual Important for the U.K, If in Doubt Consult a Competent Electrician

Page 2

Warnings, Cautions and Others

IMPORTANT for the U.K.

DO NOT cut off the mains plug from this equipment. If the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point, then obtain an appropriate safety approved extension lead or consult your dealer.

BE SURE to replace the fuse only with an identical approved type, as originally fitted.

If nonetheless the mains plug is cut off ensure to remove the fuse and dispose of the plug immediately, to avoid a possible shock hazard by inadvertent connection to the mains supply.

If this product is not supplied fitted with a mains plug then follow the instructions given below:

IMPORTANT:

DO NOT make any connection to the terminal which is marked with the letter E or by the safety earth symbol or coloured green or green-and-yellow.

The wires in the mains lead on this product are coloured in accordance with the following code:

Blue : Neutral

Brown : Live

As these colours may not correspond with the coloured markings identifying the terminals in your plug proceed as follows:

The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black.

The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red.

IF IN DOUBT - CONSULT A COMPETENT ELECTRICIAN.

Caution–– STANDBY/ON button!

Disconnect the mains plug to shut the power off completely.

The STANDBY/ON button in any position does not disconnect the mains line. The power can be remote controlled.

CAUTION

To reduce the risk of electrical shocks, fire, etc.:

1.Do not remove screws, covers or cabinet.

2.Do not expose this appliance to rain or moisture.

CAUTION

Do not block the ventilation openings or holes.

(If the ventilation openings or holes are blocked by a newspaper or cloth, etc., the heat may not be able to get out.)

Do not place any naked flame sources, such as lighted candles, on the apparatus.

When discarding batteries, environmental problems must be considered and local rules or laws governing the disposal of these batteries must be followed strictly.

Do not expose this apparatus to rain, moisture, dripping or splashing and that no objects filled with liquids such as vases, shall be placed on the apparatus.

G-1

Image 2
Contents RX-F31S LVT1306-007AImportant for the U.K If in Doubt Consult a Competent ElectricianRX-F31S Above ALL Table of Contents Parts identification Remote controlTUNING, Tuning 9, MEMORY, FM Mode Rear panel Front panelDisplay window Checking the supplied accessories Before InstallationPutting batteries in the remote control Getting startedConnecting the FM and AM MW antennas FM antenna connectionConnecting the speakers Connecting the speakersSpeaker Layout Diagram Connecting the powered subwooferScart connection Connecting video componentsScart Terminal Specifications For T-V Link Audio/video connectionFor an analogue decoder About DVD Multi Connecting another video component to the Video in jacks Connecting the power cord Digital connectionTo turn off the power into standby Turn on the powerSelecting the analogue or digital input mode Basic operationsListening with headphones Adjust the volumeSelecting the digital decode mode Activating TV Direct Adjusting the subwoofer audio positionOFF canceled Press TV DirectSignal and speaker indicators on the display Turning off the power with the Sleep TimerBasic adjustment of auto memory Turning off the sounds temporarilyTake your position where you listen to the sound Basic settingsFrom the remote control only RS LS Menu operation buttons Basic setting itemsOperation through on-screen display menus On the front panelSetup menu configuration Button indications on the screen Menu operating procedureTo select Setting MENU, press SET To select the desired submenu, press 5 or ∞ repeatedlySetting subwoofer information-SUBWOOFER Setting the itemsSetting the speakers Press SETSelecting the main or sub channel Setting the virtual surround back speakerSetting the speaker distance Setting the low frequency effect attenuator Setting bass soundUsing the Midnight mode Setting the crossover frequency-CROSSOVERAuto Mode AUTO2 Setting the Auto Function modeAuto Mode AUTO1 Auto Mode ManualSelecting the type of the input signal Superimposing the menusSound adjustments Basic adjustment itemsTOP Menu To select Adjust MENU, press SET 10 0 +10LS RS Adjusting the itemsAdjusting speaker output level Attenuating the input signal-INPUT ATT Adjusting the bass soundsSelecting the subwoofer sound phase Reinforcing the bass-BASS BoostMaking the center tone soft or sharp Adjusting the sound parameters for the Surround/DSP modesAdjusting the effect level for DSP modes To store the preset stations Tuning in to stations manuallyUsing preset tuning Tuner operationsFrom the remote control Press FM/AM to select the band Selecting the FM reception modeTo tune in a preset station Press Tuner PresetPress Display while listening to an FM station Using the Radio Data System RDS to receive FM stationsWhat information can RDS signals provide? Frequency RT Normal indicationPTY codes To search for a program using the PTY codesSearching for a program by PTY codes Press PTY Search while listening to an FM stationDescription of the PTY codes TestDisplay Canceled TA/NEWS/INFO NEWS/INFONews News Introducing the Surround modes Creating realistic sound fieldsReproducing theatre ambience Dolby DigitalDolby Surround 3D Headphone modeAbout other digital signals DTSHALL1 Introducing the DSP modesDigital Acoustic Processor DAP modes HALL2Activating the Surround/DSP modes All Channel Stereo mode ALL CH STThis mode cannot be used for multi-channel digital signals Select and play any source other than DVD Multi Turn Multi JOG to select the Surround/DSP mode you wantTo cancel Surround/DSP modes Surround modesHow does Auto Surr work? VCR Operating other JVC productsDVD recorder or DVD player Channel +DVR/DVD Changing the remote control code for DVD recorderRelease DVR/DVD TOP MENU/MENURelease TV Changing the transmittable signals for operating a TVOperating other manufacturers’ products Try to operate your TV by pressing TVTry to operate your VCR by pressing VCR Changing the transmittable signals for operating a VCRRelease VCR Manufacturers’ codes for VCRTry to operate your STB by pressing STB Changing the transmittable signals for operating an STBRelease STB Manufacturers’ codes for STBProblem Possible Cause Solution TroubleshootingPower Sound and picture Remote control Tuner FM tuner IHF SpecificationsAmplifier AM MW tuner0405RYMMDWJEIN