JVC LVT1306-007A Select and play any source other than DVD Multi, Surround modes, Press Surround

Page 46

From the remote control:

1

When operating the receiver using the remote control, set the mode selector to “AUDIO/TV/VCR/STB.”

2

1Select and play any source other than “DVD MULTI.”

•Make sure you have selected the input mode (analogue or digital) correctly.

2Press SURROUND repeatedly to select the Surround/DSP mode you want.

Ex.: When “DOLBY D” is selected for Dolby Digital multi- channel software:

	EQ C.TONE		VIRTUAL SB AUDIO P. BASS						TA NEWS INFO RDS TUNED ST AUTO MUTING SLEEP AUTO MODE
	LPCM	L		C		R		PL	ATT
	DOLBY D	S . WFR LFE						NEO : 6	HP
	DTS AAC							DSP 3D	MHz
	DTS AAC	LS	SB			RS		DSP 3D	MHz
	96 / 24	LS	SB			RS		AUTO SR	kHz

AUTO SURR						Surround modes*

HALL1						HALL2

LIVE CLUB						DANCE CLUB

PAVILION						THEATRE1

THEATRE2						MONO FILM

ALL CH ST						SURR OFF

(Back to the beginning)

To cancel Surround/DSP modes

Press SURROUND repeatedly so that “SURR OFF” appears on the display.

On the front panel:

2			1, 3

Before you start, remember...

There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 2 again.

1Select and play any source other than “DVD MULTI.”

•Make sure you have selected the input mode (analogue or digital) correctly.

2Press SURROUND.

MULTI JOG now works for selecting Surround/DSP modes.

3Turn MULTI JOG to select the Surround/DSP mode you want.

Ex.: When “DOLBY D” is selected for Dolby Digital multi- channel software:

	EQ C.TONE		VIRTUAL SB AUDIO P. BASS						TA NEWS INFO RDS TUNED ST AUTO MUTING SLEEP AUTO MODE
	LPCM	L		C		R		PL	ATT
	DOLBY D	S . WFR LFE						NEO : 6	HP
	DTS AAC							DSP 3D	MHz
	DTS AAC	LS	SB			RS		DSP 3D	MHz
	96 / 24	LS	SB			RS		AUTO SR	kHz

AUTO SURR						Surround modes*

HALL1						HALL2

LIVE CLUB						DANCE CLUB

PAVILION						THEATRE1

THEATRE2						MONO FILM

ALL CH ST						SURR OFF

(Back to the beginning)

To cancel Surround/DSP modes

Turn MULTI JOG so that “SURR OFF” appears on the display.

NOTE

The initial setting is “AUTO SURR.”

*Available Surround modes vary depending on the incoming signals. For details, see “Available Surround and DSP modes according to the incoming signal” on page 43.

42

Image 46

Contents RX-F31S LVT1306-007AImportant for the U.K If in Doubt Consult a Competent ElectricianRX-F31S Above ALL Table of Contents TUNING, Tuning 9, MEMORY, FM Mode Remote controlParts identification Display window Front panelRear panel Checking the supplied accessories Before InstallationPutting batteries in the remote control Getting startedConnecting the FM and AM MW antennas FM antenna connectionConnecting the speakers Connecting the speakersSpeaker Layout Diagram Connecting the powered subwooferScart Terminal Specifications Connecting video componentsScart connection For an analogue decoder Audio/video connectionFor T-V Link About DVD Multi Connecting another video component to the Video in jacks Connecting the power cord Digital connectionTo turn off the power into standby Turn on the powerSelecting the analogue or digital input mode Basic operationsSelecting the digital decode mode Adjust the volumeListening with headphones Activating TV Direct Adjusting the subwoofer audio positionOFF canceled Press TV DirectSignal and speaker indicators on the display Turning off the power with the Sleep TimerBasic adjustment of auto memory Turning off the sounds temporarilyFrom the remote control only Basic settingsTake your position where you listen to the sound RS LS Menu operation buttons Basic setting itemsOperation through on-screen display menus On the front panelSetup menu configuration Button indications on the screen Menu operating procedureTo select Setting MENU, press SET To select the desired submenu, press 5 or ∞ repeatedlySetting subwoofer information-SUBWOOFER Setting the itemsSetting the speakers Press SETSetting the speaker distance Setting the virtual surround back speakerSelecting the main or sub channel Setting the low frequency effect attenuator Setting bass soundUsing the Midnight mode Setting the crossover frequency-CROSSOVERAuto Mode AUTO2 Setting the Auto Function modeAuto Mode AUTO1 Auto Mode ManualSelecting the type of the input signal Superimposing the menusSound adjustments Basic adjustment itemsTOP Menu To select Adjust MENU, press SET 10 0 +10Adjusting speaker output level Adjusting the itemsLS RS Attenuating the input signal-INPUT ATT Adjusting the bass soundsSelecting the subwoofer sound phase Reinforcing the bass-BASS BoostAdjusting the effect level for DSP modes Adjusting the sound parameters for the Surround/DSP modesMaking the center tone soft or sharp To store the preset stations Tuning in to stations manuallyUsing preset tuning Tuner operationsFrom the remote control Press FM/AM to select the band Selecting the FM reception modeTo tune in a preset station Press Tuner PresetPress Display while listening to an FM station Using the Radio Data System RDS to receive FM stationsWhat information can RDS signals provide? Frequency RT Normal indicationPTY codes To search for a program using the PTY codesSearching for a program by PTY codes Press PTY Search while listening to an FM stationDescription of the PTY codes TestNews News Canceled TA/NEWS/INFO NEWS/INFODisplay Introducing the Surround modes Creating realistic sound fieldsReproducing theatre ambience Dolby DigitalDolby Surround 3D Headphone modeAbout other digital signals DTSHALL1 Introducing the DSP modesDigital Acoustic Processor DAP modes HALL2This mode cannot be used for multi-channel digital signals All Channel Stereo mode ALL CH STActivating the Surround/DSP modes Select and play any source other than DVD Multi Turn Multi JOG to select the Surround/DSP mode you wantTo cancel Surround/DSP modes Surround modesHow does Auto Surr work? VCR Operating other JVC productsDVD recorder or DVD player Channel +DVR/DVD Changing the remote control code for DVD recorderRelease DVR/DVD TOP MENU/MENURelease TV Changing the transmittable signals for operating a TVOperating other manufacturers’ products Try to operate your TV by pressing TVTry to operate your VCR by pressing VCR Changing the transmittable signals for operating a VCRRelease VCR Manufacturers’ codes for VCRTry to operate your STB by pressing STB Changing the transmittable signals for operating an STBRelease STB Manufacturers’ codes for STBPower Sound and picture Remote control Tuner TroubleshootingProblem Possible Cause Solution FM tuner IHF SpecificationsAmplifier AM MW tuner0405RYMMDWJEIN