JVC LVT1306-007A Operating other manufacturers’ products, Release TV, Manufacturers’ codes for TV

Page 50

Operating other manufacturers’ products

By changing the transmittable signals, you can use the supplied remote control to operate other manufacturers’ products.

•Refer also to the manuals supplied with the other products.

•To operate those components with the remote control, first you need to set the manufacturers’ codes each for the TV, VCR, and STB.

•After replacing batteries of the remote control, set the manufacturers’ codes again.

❏Changing the transmittable signals for operating a TV

Set the mode selector to “AUDIO/TV/VCR/STB.”

1Press and hold TV .

2Press TV.

3Enter the manufacturer’s code using buttons 1 – 9, and 0.

See “Manufacturers’ codes for TV” on the right.

4Release TV .

Now, you can perform the following operations on the TV.

TV :	Turn on or off the TV.
TV VOL +/–:	Adjust the volume on the TV.

TV/VIDEO:	Change the input mode (either TV or
	VIDEO).

After pressing TV, you can perform the following operations on the TV.

CHANNEL +/–:Change the channel numbers.

1 – 9, 0, 100+ (+10): Select the channel numbers.

See the instructions supplied with the TV for details.

5Try to operate your TV by pressing TV .

When your TV turns on or off, you have entered the correct

code.

If more than one code is listed for your brand of TV, try each

one until the correct one is entered.

Manufacturers’ codes for TV

Manufacturer	Codes

JVC	01
Akai	02, 05
Blaupunkt	03
Daewoo	09, 30, 31
Fenner	04, 30, 31
Fisher	05
Grundig	06
Hitachi	07, 08
Irradio	02, 05
Magnavox	09
Mitsubishi	10, 32
Mivar	03
Nokia	11, 33
Nordmende	12, 13, 17, 25 – 27
Orion	14
Panasonic	15, 16
Philips	09
Saba	12, 13, 17, 25 – 27
Samsung	09, 18, 31
Sanyo	05
Schneider	02, 05
Sharp	19
Sony	20 – 24
Telefunken	12, 13, 17, 25 – 27
Thomson	12, 13, 17, 25 – 27, 29
Toshiba	28

Initial setting: 01

Manufacturers’ codes are subject to change without notice. If they are changed, this remote control cannot operate the equipment.

46

Image 50

Contents RX-F31S LVT1306-007AImportant for the U.K If in Doubt Consult a Competent ElectricianRX-F31S Above ALL Table of Contents Parts identification Remote controlTUNING, Tuning 9, MEMORY, FM Mode Rear panel Front panelDisplay window Checking the supplied accessories Before InstallationPutting batteries in the remote control Getting startedConnecting the FM and AM MW antennas FM antenna connectionConnecting the speakers Connecting the speakersSpeaker Layout Diagram Connecting the powered subwooferScart connection Connecting video componentsScart Terminal Specifications For T-V Link Audio/video connectionFor an analogue decoder About DVD Multi Connecting another video component to the Video in jacks Connecting the power cord Digital connectionTo turn off the power into standby Turn on the powerSelecting the analogue or digital input mode Basic operationsListening with headphones Adjust the volumeSelecting the digital decode mode Activating TV Direct Adjusting the subwoofer audio positionOFF canceled Press TV DirectSignal and speaker indicators on the display Turning off the power with the Sleep TimerBasic adjustment of auto memory Turning off the sounds temporarilyTake your position where you listen to the sound Basic settingsFrom the remote control only RS LS Menu operation buttons Basic setting itemsOperation through on-screen display menus On the front panelSetup menu configuration Button indications on the screen Menu operating procedureTo select Setting MENU, press SET To select the desired submenu, press 5 or ∞ repeatedlySetting subwoofer information-SUBWOOFER Setting the itemsSetting the speakers Press SETSelecting the main or sub channel Setting the virtual surround back speakerSetting the speaker distance Setting the low frequency effect attenuator Setting bass soundUsing the Midnight mode Setting the crossover frequency-CROSSOVERAuto Mode AUTO2 Setting the Auto Function modeAuto Mode AUTO1 Auto Mode ManualSelecting the type of the input signal Superimposing the menusSound adjustments Basic adjustment itemsTOP Menu To select Adjust MENU, press SET 10 0 +10LS RS Adjusting the itemsAdjusting speaker output level Attenuating the input signal-INPUT ATT Adjusting the bass soundsSelecting the subwoofer sound phase Reinforcing the bass-BASS BoostMaking the center tone soft or sharp Adjusting the sound parameters for the Surround/DSP modesAdjusting the effect level for DSP modes To store the preset stations Tuning in to stations manuallyUsing preset tuning Tuner operationsFrom the remote control Press FM/AM to select the band Selecting the FM reception modeTo tune in a preset station Press Tuner PresetPress Display while listening to an FM station Using the Radio Data System RDS to receive FM stationsWhat information can RDS signals provide? Frequency RT Normal indicationPTY codes To search for a program using the PTY codesSearching for a program by PTY codes Press PTY Search while listening to an FM stationDescription of the PTY codes TestDisplay Canceled TA/NEWS/INFO NEWS/INFONews News Introducing the Surround modes Creating realistic sound fieldsReproducing theatre ambience Dolby DigitalDolby Surround 3D Headphone modeAbout other digital signals DTSHALL1 Introducing the DSP modesDigital Acoustic Processor DAP modes HALL2Activating the Surround/DSP modes All Channel Stereo mode ALL CH STThis mode cannot be used for multi-channel digital signals Select and play any source other than DVD Multi Turn Multi JOG to select the Surround/DSP mode you wantTo cancel Surround/DSP modes Surround modesHow does Auto Surr work? VCR Operating other JVC productsDVD recorder or DVD player Channel +DVR/DVD Changing the remote control code for DVD recorderRelease DVR/DVD TOP MENU/MENURelease TV Changing the transmittable signals for operating a TVOperating other manufacturers’ products Try to operate your TV by pressing TVTry to operate your VCR by pressing VCR Changing the transmittable signals for operating a VCRRelease VCR Manufacturers’ codes for VCRTry to operate your STB by pressing STB Changing the transmittable signals for operating an STBRelease STB Manufacturers’ codes for STBProblem Possible Cause Solution TroubleshootingPower Sound and picture Remote control Tuner FM tuner IHF SpecificationsAmplifier AM MW tuner0405RYMMDWJEIN