JVC LVT1306-007A manual Specifications, Amplifier, FM tuner IHF, AM MW tuner, General

Page 54

Specifications

Designs and specifications are subject to change without notice.

Amplifier

Output Power

At stereo operation:
Front channels:	100 W per channel, min. RMS, both
	channels driven into 6 Ω at 1 kHz with no
	more than 10% total harmonic distortion.
	(IEC268-3)

At surround operation:

Front channels:	100 W per channel, min. RMS, driven into
	6 Ω at 1 kHz with no more than 0.8% total
	harmonic distortion.
Center channel:	100 W, min. RMS, driven into 6 Ω at 1 kHz,
	with no more than 0.8% total harmonic
	distortion.

Surround channels: 100 W per channel, min. RMS, driven into 6 Ω at 1 kHz, with no more than 0.8% total harmonic distortion.

Audio

Audio Input Sensitivity/Impedance:

VIDEO, DVD MULTI, DVR/DVD, VCR, TV:

330 mV/47 kΩ

Audio Input (DIGITAL IN)*:

Coaxial: DIGITAL IN 1(DVR/DVD):

0.5 V(p-p)/75 Ω

Optical: DIGITAL IN 2(VIDEO), 3(TV):

–21 dBm to –15 dBm (660 nm ±30 nm)

*Corresponding to Linear PCM, Dolby Digital, and DTS (with sampling frequency—32 kHz, 44.1 kHz, 48 kHz).

Audio Output Level:

MONITOR OUT, DVR/DVD, VCR, TV:

	330 mV
Signal-to-Noise Ratio (’66 IHF/DIN): 80 dB/62 dB
Frequency Response (6 Ω):	20 Hz to 20 kHz (±1 dB)
Bass Boost:	+4 dB ±1 dB at 100 Hz

Equalization:
Center frequency:	63 Hz, 250 Hz, 1 kHz, 4 kHz, 16 kHz
Control range:	±8 dB

Video

Video Input Sensitivity/Impedance:

Composite video: DVR/DVD, VCR, TV, VIDEO:

	1 V(p-p)/75 Ω
S-video: DVR/DVD, VCR, VIDEO:
Y (luminance):	1 V(p-p)/75 Ω
C (chrominance, burst):	0.3 V(p-p)/75 Ω
RGB: DVR/DVD, VCR:	0.7 V(p-p)/75 Ω
Component: DVR/DVD, VIDEO:
Y (luminance):	1 V(p-p)/75 Ω
PB, PR:	0.7 V(p-p)/75 Ω

Video Output Level/Impedance:

Composite video: DVR/DVD, VCR, TV:

	1 V(p-p)/75 Ω
S-video: TV:
Y (luminance):	1 V(p-p)/75 Ω
C (chrominance, burst):	0.3 V(p-p)/75 Ω
RGB: TV:	0.7 V(p-p)/75 Ω
Component: MONITOR OUT:
Y (luminance):	1 V(p-p)/75 Ω
PB, PR:	0.7 V(p-p)/75 Ω
Synchronization:	Negative

FM tuner (IHF)

Tuning Range:	87.50 MHz to 108.00 MHz
Usable Sensitivity:
Monaural:	17.0 dBf (1.95 µV/75 Ω)
50 dB Quieting Sensitivity:
Monaural:	21.3 dBf (3.2 µV/75 Ω)
Stereo:	41.3 dBf (31.5 µV/75 Ω)
Stereo Separation at Rec out:	35 dB at 1 kHz

AM (MW) tuner

Tuning Range:522 kHz to 1 629 kHz

General

Power Requirements:	AC 230 V , 50 Hz
Power Consumption:	110 W (at operation)
	2 W (in standby mode)

Dimensions (W x H x D): 435 mm x 70 mm x 317.2 mm

Mass:

6.3 kg

50

Image 54

Contents RX-F31S LVT1306-007AImportant for the U.K If in Doubt Consult a Competent ElectricianRX-F31S Above ALL Table of Contents Remote control TUNING, Tuning 9, MEMORY, FM ModeParts identification Front panel Display windowRear panel Checking the supplied accessories Before InstallationPutting batteries in the remote control Getting startedConnecting the FM and AM MW antennas FM antenna connectionConnecting the speakers Connecting the speakersSpeaker Layout Diagram Connecting the powered subwooferConnecting video components Scart Terminal SpecificationsScart connection Audio/video connection For an analogue decoderFor T-V Link About DVD Multi Connecting another video component to the Video in jacks Connecting the power cord Digital connectionTo turn off the power into standby Turn on the powerSelecting the analogue or digital input mode Basic operationsAdjust the volume Selecting the digital decode modeListening with headphones Activating TV Direct Adjusting the subwoofer audio positionOFF canceled Press TV DirectSignal and speaker indicators on the display Turning off the power with the Sleep TimerBasic adjustment of auto memory Turning off the sounds temporarilyBasic settings From the remote control onlyTake your position where you listen to the sound RS LS Menu operation buttons Basic setting itemsOperation through on-screen display menus On the front panelSetup menu configuration Button indications on the screen Menu operating procedureTo select Setting MENU, press SET To select the desired submenu, press 5 or ∞ repeatedlySetting subwoofer information-SUBWOOFER Setting the itemsSetting the speakers Press SETSetting the virtual surround back speaker Setting the speaker distanceSelecting the main or sub channel Setting the low frequency effect attenuator Setting bass soundUsing the Midnight mode Setting the crossover frequency-CROSSOVERAuto Mode AUTO2 Setting the Auto Function modeAuto Mode AUTO1 Auto Mode ManualSelecting the type of the input signal Superimposing the menusSound adjustments Basic adjustment itemsTOP Menu To select Adjust MENU, press SET 10 0 +10Adjusting the items Adjusting speaker output levelLS RS Attenuating the input signal-INPUT ATT Adjusting the bass soundsSelecting the subwoofer sound phase Reinforcing the bass-BASS BoostAdjusting the sound parameters for the Surround/DSP modes Adjusting the effect level for DSP modesMaking the center tone soft or sharp To store the preset stations Tuning in to stations manuallyUsing preset tuning Tuner operationsFrom the remote control Press FM/AM to select the band Selecting the FM reception modeTo tune in a preset station Press Tuner PresetPress Display while listening to an FM station Using the Radio Data System RDS to receive FM stationsWhat information can RDS signals provide? Frequency RT Normal indicationPTY codes To search for a program using the PTY codesSearching for a program by PTY codes Press PTY Search while listening to an FM stationDescription of the PTY codes TestCanceled TA/NEWS/INFO NEWS/INFO News NewsDisplay Introducing the Surround modes Creating realistic sound fieldsReproducing theatre ambience Dolby DigitalDolby Surround 3D Headphone modeAbout other digital signals DTSHALL1 Introducing the DSP modesDigital Acoustic Processor DAP modes HALL2All Channel Stereo mode ALL CH ST This mode cannot be used for multi-channel digital signalsActivating the Surround/DSP modes Select and play any source other than DVD Multi Turn Multi JOG to select the Surround/DSP mode you wantTo cancel Surround/DSP modes Surround modesHow does Auto Surr work? VCR Operating other JVC productsDVD recorder or DVD player Channel +DVR/DVD Changing the remote control code for DVD recorderRelease DVR/DVD TOP MENU/MENURelease TV Changing the transmittable signals for operating a TVOperating other manufacturers’ products Try to operate your TV by pressing TVTry to operate your VCR by pressing VCR Changing the transmittable signals for operating a VCRRelease VCR Manufacturers’ codes for VCRTry to operate your STB by pressing STB Changing the transmittable signals for operating an STBRelease STB Manufacturers’ codes for STBTroubleshooting Power Sound and picture Remote control TunerProblem Possible Cause Solution FM tuner IHF SpecificationsAmplifier AM MW tuner0405RYMMDWJEIN