JVC LVT1306-007A manual Using the Radio Data System RDS to receive FM stations

Page 38

Using the Radio Data System (RDS) to receive FM stations

Only the buttons on the remote control are used for RDS operations.

When operating the receiver using the remote control, set the mode selector to “AUDIO/TV/VCR/STB.”

RDS allows FM stations to send an additional signal along with their regular program signals. For example, the stations send their station names, as well as information about what type of program they broadcast, such as sports or music, etc.

When an FM station which provides the RDS service is tuned in, the RDS indicator lights up on the display.

 

 

 

 

 

 

 

RDS indicator

 

 

 

 

 

 

 

 

 

 

 

 

 

EQ C.TONE

VIRTUAL SB AUDIO P. BASS

TA NEWS INFO RDS TUNED ST AUTO MUTING SLEEP AUTO MODE

LPCM

L

C

R

 

PL

 

ATT

DOLBY D

S . WFR LFE

NEO : 6

 

HP

DTS AAC

 

 

 

 

 

DSP 3D

 

MHz

LS

SB

RS

96 / 24

AUTO SR

 

kHz

 

 

 

 

 

 

 

 

 

With the receiver, you can receive the following types of RDS signals:

PS (Program Service):

Shows commonly known station

 

names.

 

 

PTY (Program Type):

Shows types of broadcast

 

programs.

 

 

RT (Radio Text):

Shows text messages the station

 

sends.

 

 

Enhanced Other Networks:

See page 37.

 

 

NOTES

•RDS is not available for AM (MW) broadcasts.

•RDS may not operate correctly if the station tuned is not transmitting RDS signal properly or if the signal strength is weak.

What information can RDS signals provide?

You can see the RDS signals the station sends on the display.

Press DISPLAY while listening to an FM station.

•Each time you press the button, the display changes to show the following information:

PS PTY

Frequency RT (Normal indication)

PS (Program Service):

While searching, “PS” appears and then the station names will be displayed. “NO PS” appears if no signal is sent.

PTY (Program Type):

While searching, “PTY” appears and then the type of the broadcast program will be displayed. “NO PTY” appears if no signal is sent.

RT (Radio Text):

While searching, “RT” appears and then text messages the station sends will be displayed. “NO RT” appears if no signal is sent.

Frequency:

Station frequency (non-RDS service).

About characters shown on the display

When the display shows PS, PTY, or RT signals, the following characters are used:

•The display cannot show accented letters, “A” for instance, may stand for accented “A’s” like “Å, Ä, Ã, Á, À, Â, å, ä, ã, á, à, and â.”

NOTE

If searching finishes at once, “PS,” “PTY,” and “RT” will not appear on the display.

34

Page 37 Page 39
Image 38
Page 37 Page 39
Contents RX-F31S LVT1306-007AImportant for the U.K If in Doubt Consult a Competent ElectricianRX-F31S Above ALL Table of Contents Parts identification Remote controlTUNING, Tuning 9, MEMORY, FM Mode Rear panel Front panelDisplay window Checking the supplied accessories Before InstallationPutting batteries in the remote control Getting startedConnecting the FM and AM MW antennas FM antenna connectionConnecting the speakers Connecting the speakersSpeaker Layout Diagram Connecting the powered subwooferScart connection Connecting video componentsScart Terminal Specifications For T-V Link Audio/video connectionFor an analogue decoder About DVD Multi Connecting another video component to the Video in jacks Connecting the power cord Digital connectionTo turn off the power into standby Turn on the powerSelecting the analogue or digital input mode Basic operationsListening with headphones Adjust the volumeSelecting the digital decode mode Activating TV Direct Adjusting the subwoofer audio positionOFF canceled Press TV DirectSignal and speaker indicators on the display Turning off the power with the Sleep TimerBasic adjustment of auto memory Turning off the sounds temporarilyTake your position where you listen to the sound Basic settingsFrom the remote control only RS LS Menu operation buttons Basic setting itemsOperation through on-screen display menus On the front panelSetup menu configuration Button indications on the screen Menu operating procedureTo select Setting MENU, press SET To select the desired submenu, press 5 or ∞ repeatedlySetting subwoofer information-SUBWOOFER Setting the itemsSetting the speakers Press SETSelecting the main or sub channel Setting the virtual surround back speakerSetting the speaker distance Setting the low frequency effect attenuator Setting bass soundUsing the Midnight mode Setting the crossover frequency-CROSSOVERAuto Mode AUTO2 Setting the Auto Function modeAuto Mode AUTO1 Auto Mode ManualSelecting the type of the input signal Superimposing the menusSound adjustments Basic adjustment itemsTOP Menu To select Adjust MENU, press SET 10 0 +10LS RS Adjusting the itemsAdjusting speaker output level Attenuating the input signal-INPUT ATT Adjusting the bass soundsSelecting the subwoofer sound phase Reinforcing the bass-BASS BoostMaking the center tone soft or sharp Adjusting the sound parameters for the Surround/DSP modesAdjusting the effect level for DSP modes To store the preset stations Tuning in to stations manuallyUsing preset tuning Tuner operationsFrom the remote control Press FM/AM to select the band Selecting the FM reception modeTo tune in a preset station Press Tuner PresetPress Display while listening to an FM station Using the Radio Data System RDS to receive FM stationsWhat information can RDS signals provide? Frequency RT Normal indicationPTY codes To search for a program using the PTY codesSearching for a program by PTY codes Press PTY Search while listening to an FM stationDescription of the PTY codes TestDisplay Canceled TA/NEWS/INFO NEWS/INFONews News Introducing the Surround modes Creating realistic sound fieldsReproducing theatre ambience Dolby DigitalDolby Surround 3D Headphone modeAbout other digital signals DTSHALL1 Introducing the DSP modesDigital Acoustic Processor DAP modes HALL2Activating the Surround/DSP modes All Channel Stereo mode ALL CH STThis mode cannot be used for multi-channel digital signals Select and play any source other than DVD Multi Turn Multi JOG to select the Surround/DSP mode you wantTo cancel Surround/DSP modes Surround modesHow does Auto Surr work? VCR Operating other JVC productsDVD recorder or DVD player Channel +DVR/DVD Changing the remote control code for DVD recorderRelease DVR/DVD TOP MENU/MENURelease TV Changing the transmittable signals for operating a TVOperating other manufacturers’ products Try to operate your TV by pressing TVTry to operate your VCR by pressing VCR Changing the transmittable signals for operating a VCRRelease VCR Manufacturers’ codes for VCRTry to operate your STB by pressing STB Changing the transmittable signals for operating an STBRelease STB Manufacturers’ codes for STBProblem Possible Cause Solution TroubleshootingPower Sound and picture Remote control Tuner FM tuner IHF SpecificationsAmplifier AM MW tuner0405RYMMDWJEIN
Top Page Image Contents