JVC LVT1306-007A manual Connecting the FM and AM MW antennas, FM antenna connection

Page 9

Connecting the FM and AM (MW) antennas

Do not connect the AC power plug to the wall outlet until all connections are completed.

AM (MW) loop antenna (supplied)

If AM (MW) reception is poor, connect an outdoor single vinyl- covered wire (not supplied).

Snap the tabs on the loop into the slots of the base to assemble the AM (MW) loop antenna.

If FM reception is poor, connect an outdoor FM antenna (not supplied).

AM LOOP	ANTENNA
	ANTENNA
	FM 75

AM EXT

COAXIAL

FM antenna (supplied)

AM (MW) antenna connection

NOTES

Connect the AM (MW) loop antenna supplied to the AM LOOP terminals.

Connect the white cord to the AM EXT terminal, and connect the black cord to the H terminal.

Turn the loop until you have the best reception.

•If the reception is poor, connect an outdoor single vinyl-covered wire (not supplied) to the AM EXT terminal. Keep the AM (MW) loop antenna connected.

•If the AM (MW) loop antenna wire is covered with vinyl, remove the vinyl while twisting it as shown on the right.

•Make sure the antenna conductors do not touch any other terminals, connecting cords and power cord. This could cause poor reception.

FM antenna connection

Connect the FM antenna supplied to the FM 75 Ω COAXIAL terminal as a temporary measure.

Extend the supplied FM antenna horizontally.

•If the reception is poor, connect an outdoor FM antenna (not supplied). Before attaching a 75 Ω coaxial cable with a connector (IEC or DIN 45325) , disconnect the supplied FM antenna.

5

Image 9

Contents LVT1306-007A RX-F31SIf in Doubt Consult a Competent Electrician Important for the U.KRX-F31S Above ALL Table of Contents Remote control TUNING, Tuning 9, MEMORY, FM ModeParts identification Front panel Display windowRear panel Putting batteries in the remote control Before InstallationChecking the supplied accessories Getting startedFM antenna connection Connecting the FM and AM MW antennasSpeaker Layout Diagram Connecting the speakersConnecting the speakers Connecting the powered subwooferConnecting video components Scart Terminal SpecificationsScart connection Audio/video connection For an analogue decoderFor T-V Link About DVD Multi Connecting another video component to the Video in jacks Digital connection Connecting the power cordSelecting the analogue or digital input mode Turn on the powerTo turn off the power into standby Basic operationsAdjust the volume Selecting the digital decode modeListening with headphones OFF canceled Adjusting the subwoofer audio positionActivating TV Direct Press TV DirectBasic adjustment of auto memory Turning off the power with the Sleep TimerSignal and speaker indicators on the display Turning off the sounds temporarilyBasic settings From the remote control onlyTake your position where you listen to the sound RS LS Operation through on-screen display menus Basic setting itemsMenu operation buttons On the front panelSetup menu configuration To select Setting MENU, press SET Menu operating procedureButton indications on the screen To select the desired submenu, press 5 or ∞ repeatedlySetting the speakers Setting the itemsSetting subwoofer information-SUBWOOFER Press SETSetting the virtual surround back speaker Setting the speaker distanceSelecting the main or sub channel Using the Midnight mode Setting bass soundSetting the low frequency effect attenuator Setting the crossover frequency-CROSSOVERAuto Mode AUTO1 Setting the Auto Function modeAuto Mode AUTO2 Auto Mode ManualSuperimposing the menus Selecting the type of the input signalBasic adjustment items Sound adjustmentsTOP Menu 10 0 +10 To select Adjust MENU, press SETAdjusting the items Adjusting speaker output levelLS RS Selecting the subwoofer sound phase Adjusting the bass soundsAttenuating the input signal-INPUT ATT Reinforcing the bass-BASS BoostAdjusting the sound parameters for the Surround/DSP modes Adjusting the effect level for DSP modesMaking the center tone soft or sharp Using preset tuning Tuning in to stations manuallyTo store the preset stations Tuner operationsTo tune in a preset station Selecting the FM reception modeFrom the remote control Press FM/AM to select the band Press Tuner PresetWhat information can RDS signals provide? Using the Radio Data System RDS to receive FM stationsPress Display while listening to an FM station Frequency RT Normal indicationSearching for a program by PTY codes To search for a program using the PTY codesPTY codes Press PTY Search while listening to an FM stationTest Description of the PTY codesCanceled TA/NEWS/INFO NEWS/INFO News NewsDisplay Reproducing theatre ambience Creating realistic sound fieldsIntroducing the Surround modes Dolby DigitalAbout other digital signals 3D Headphone modeDolby Surround DTSDigital Acoustic Processor DAP modes Introducing the DSP modesHALL1 HALL2All Channel Stereo mode ALL CH ST This mode cannot be used for multi-channel digital signalsActivating the Surround/DSP modes To cancel Surround/DSP modes Turn Multi JOG to select the Surround/DSP mode you wantSelect and play any source other than DVD Multi Surround modesHow does Auto Surr work? DVD recorder or DVD player Operating other JVC productsVCR Channel +Release DVR/DVD Changing the remote control code for DVD recorderDVR/DVD TOP MENU/MENUOperating other manufacturers’ products Changing the transmittable signals for operating a TVRelease TV Try to operate your TV by pressing TVRelease VCR Changing the transmittable signals for operating a VCRTry to operate your VCR by pressing VCR Manufacturers’ codes for VCRRelease STB Changing the transmittable signals for operating an STBTry to operate your STB by pressing STB Manufacturers’ codes for STBTroubleshooting Power Sound and picture Remote control TunerProblem Possible Cause Solution Amplifier SpecificationsFM tuner IHF AM MW tuner0405RYMMDWJEIN