Miele WT 945 S WPS, wt945 Wash programme stops and a fault indicator light comes on

Page 45

Problem solving guide

The wash programme stops and a fault indicator light comes on.

Problem	Possible cause	Remedy

The Water inlet/drain	The water inlet system	– Turn the programme
indicator lamp is	is blocked.	selectors to Finish.
flashing and the load in		– Open the stopcock.
the machine has not		– Select and start the
been washed.		– Select and start the
been washed.		programme again.
		programme again.

The Water inlet/drain	There is a blockage in	– Clean the fluff filter and
indicator lamp is	the water outlet.	the drain pump.
flashing.		– Has the drain hose been
		fitted too high? Maximum
		delivery head 1.00 m.

	The Waterproof system	– Call the Miele Service
	has reacted.	department.

The Final spin indicator	The final spin has not	– Loosen the laundry.
lamp is flashing in the	taken place. The	– Turn the WASHING
programme sequence	machine detected an	programme selector to
display.	imbalance.	Spin.
		– Make sure you select an
		appropriate spin speed
		for the type of load.

45

Image 45

Contents Operating instructions Washer-dryer WT 945 S WPS Contents Contents Consumption data Technical data Caring for the environment Disposal of the packing materialDisposal of your old appliance or machine Correct usage Technical safetyUse Disposal of your old machine Using accessoriesDescription of the appliance FeaturesStart button Control panelDoor button Opens the drum door On / 0-OFF button Additional option buttonsImportant control panel features Spin button with indicator lampsProgramme selector Washing and drying environmentally Before using for the first time Flushing out the drumWater hardness reminder Programme overview Cottons eMinimum Iron e f Delicates f Woollens gQuick wash Drain / Spin StarchSeparate rinse Flushing out the drumHow to wash correctly Important other care symbols How to wash correctlyTumble dry IroningSeparate washing Before washingSort the laundry Select a programme Soak Detergent dispensing when selecting the soak optionPre-wash Water plusAdding detergent At the end of a programme Door cannot be opened, if Adding and removing laundryCottons Programme cycleQuick Wash Special features in the programme sequencesDetergent Adding detergentWater softener Washing with several componentsFabric conditioners, texturisers and starch Fabric conditioners / starch formulationsAdding fabric conditioner or liquid starch separately Separate starchingFollowing fabrics should not be tumble dried Tips on dryingProgramme overview Always select the Drying / Low temp. option Timed Drying 20 min / 30 min / 40 min / 60 minSeparate drying Before dryingPreparing the laundry Programme selection Select a drying programmeDrying / Low temp After drying Washing and drying in a continuous sequence Close the drum door Open the stopcock Add detergentSelect the programme After each washing or drying programme Rinse out fluff programme To cancel an incorrectly selected programme To cancel a programmeChanging a programme sequence To change a programme which has been lockedSafety lock Safety lockEngaging the safety lock Cleaning the machine Cleaning and careCleaning the detergent dispenser ClothClean the siphon tube Clean the porthole glassCleaning the filter in the water inlet What to do if ... ? Problem solving guideDept Programme does not startWash programme stops and a fault indicator light comes on Locked indicator lamp Indicator lamp flashesDuring a programme But the washGeneral problems or an unsatisfactory wash or drying result Option Opened during or afterDrying When washing Problem Possible cause Remedy Laundry is stillWhen drying separately Damp after a dryingSpun satisfactorily Problem Possible cause Remedy Laundry is notMachine is not Steady during a spinBuild-up of foam Problem Possible cause Remedy There is an excessiveWhite residues which Look like powderNot give the required Problem Possible cause Remedy Liquid detergent doesResult Remember to removeBlocked drain outlet Opening the drum door Appliance guarantee After sales serviceFront view Installation and connectionInstallation surface InstallationPlease note the following Removing the transit fitting Levelling the machine Screwing out and adjusting the feetInstallation and connection Miele Waterproof system Electronic unit and washing machine housingInlet hose Drain hoseConnection to the water supply Installation and connection Maintenance and care Drain hose connection Connection to the drainage systemElectrical connection U.K Non-rewireable plugs BSProgrammes Consumption dataTechnical data Programmable functions for changing standard settings High water level Programmable functionsAdditional rinse for Cottons programme Buzzer Opening the door at high temperatures Final residual moisture after drying Factory settingShortening the drying time Lengthening the drying timePage Alteration rights reserved / 3404 / WT 945 S