Miele T 8822 C operating instructions Technical safety

Page 6

Warning and Safety instructions

Technical safety

￿Before setting up the tumble dryer, check it for any externally visible damage.

Do not install or use a damaged tumble dryer.

￿Before connecting the tumble dryer, ensure that the connection data on the data plate (voltage and connected load) match the mains electricity supply. If in any doubt, consult a qualified electrician.

￿The electrical safety of this tumble dryer can only be guaranteed when continuity is complete between it and an effective earthing system which complies with current local and national safety regulations. It is most important that this basic safety requirement is present and regularly tested, and where there is any doubt the household wiring system should be inspected by a qualified electrician. Miele cannot be held liable for the consequences of an inadequate earthing system (e.g. electric shock).

￿Faulty components must only be replaced by genuine Miele original spare parts. Only when these parts are fitted can the safety standards of the tumble dryer be guaranteed.

￿If the connection cable is faulty it must only be replaced by a Miele approved service technician to protect the user from danger.

￿In the event of a fault or for cleaning purposes, the tumble dryer is only completely isolated from the electricity supply when:

it is switched off at the wall socket and the plug is withdrawn, or

it is switched off at the mains, or

the mains fuse is disconnected, or

the screw-out fuse is removed (in countries where this is applicable).

￿This tumble dryer may only be used in mobile installations such as ships if a risk assessment of the installation has been carried out by a suitably qualified engineer.

￿Do not connect the tumble dryer to the mains electricity supply by an extension lead. Extension leads do not guarantee the required safety of the tumble dryer (e.g. danger of overheating).

￿Unauthorised repairs could result in unforeseen dangers for the user, for which Miele cannot accept liability. Repairs should only be undertaken by a Miele approved service technician. Ensure current is not supplied to the tumble dryer until after maintenance or repair work has been carried out.

￿In countries where there are areas which may be subject to infestation by cockroaches or other vermin, pay particular attention to keeping the tumble dryer and its surroundings in a clean condition at all times. Any damage which may be caused by cockroaches or other vermin will not be covered by the guarantee.

￿Do not make any alterations to the tumble dryer, unless authorised to do so by Miele.

6

Image 6
Contents Operating instructions For condenser tumble dryer T 8822 C Disposal of your old appliance Caring for the environmentDisposal of the packing material Energy saving tipsContents Contents Safety with children Correct applicationTechnical safety Correct use Accessories Operating the tumble dryer Control panelProgramme duration / Estimated time remaining Display showsFollowing are also selected via the display Drying Garment care label symbolsTips on drying IroningSort the laundry How to dry correctlyBrief instructions Turn on the tumble dryerSelect any Extra options / Delay start Select a programmeDrying level programmes Remove the laundry when the programme has finished Start the programmeBefore the end of a programme Extra options / Delay start Delay startExtra options Hand iron**, Machine iron Programme chartCottons Max. load 7 kg Extra dry, Normal Delicates Max. load 2.5 kg Normal, Hand ironOnly use proofing agents which are stated by Woollens handcare Max. load 2 kgProofing Max. load 2.5 kg Normal Manufacturer as being suitable for use on membraneWarm air Max. load 7 kg Shirts Max. load 2 kg Normal, Hand ironCool air Max. load 7 kg Gentle smoothing Max. load 1 kgOnce a programme has started Altering Delay startChanging the programme sequence Adding or removing laundry after a programme has startedElectronic system lock To activate the lockTo deactivate the lock Cleaning and care Emptying the condensed water containerCleaning the fluff filters Cleaning them whilst dryCleaning them with water Cleaning the tumble dryer Cleaning the condenser unit Removing the condenser unitChecking the condenser unit Checking and cleaning the condenser unit housing Problem solving guide Check and fault messagesTo switch off the indicator Problem Possible cause RemedyAirways indicator Buzzer sounds To switch off the indicator LightWill not start Indicators for theseCool air programmes Programmes do notAn unsatisfactory drying result Even switches off Other problemsProblem Possible cause Remedy Drying process Goes on too long orPower cut Problem Possible cause Remedy Water leaks fromBeen cleaned Dryer afterChanging the lamp Appliance guarantee After Sales serviceFuture updates PC Optional accessoriesInstallation Front viewRear view Installation siteTransporting the dryer to its installation site Replacing the lidRoom ventilation Before moving the tumble dryer again e.g. when moving houseLevelling the appliance Washer-dryer stackExternal condensed water outlet General notesArranging the drain hose Installation conditions requiring a non-return valve External drainage via a sink or gullyInstallation Non-rewireable plugs BS Electrical connectionElectrical connection U.K Consumption data Woollens handcareTechnical data Programmable functions Extending the range of the drying levelsAnti-crease setting Anti-crease deactivated Hour anti-creaseHours anti-crease Altering the volume of the buzzer Normal buzzer Default setting Loud buzzerMemory deactivated default setting Memory activated Memory functionExtending the cooling down time Follow steps to to programme and store in memoryCooling down time will be ten minutes longer Clean out airways indicator Default settingKeypad tone Adjusting the dryers electronics for very soft water Default setting Adjusted for very soft waterPage Page Page Alteration rights reserved/1409 Nr 483 560
Related manuals
Manual 64 pages 59 Kb