Alliance Laundry Systems 33, 75, 40, 100, 135, 165, 200, 18, 55 manual Model

Page 22

Specifications and Dimensions

60.8 in.

(1544 mm)

33.8 in.

(859 mm)

22 in.

(559 mm)

5
5			40 in.
			40 in.
			(1016 mm)
			(1016 mm)

59 in.

(1499 mm)

	29.13 in.
	(740 mm)					32.68 in.
						32.68 in.
	35.43 in.					(830 mm)
	(900 mm)	CFD509N
		CFD509N
				13.6 in.
				(91 mm)
	10 in.
	(254 mm)
				9.9 in.
			(252 mm)
	6.2 in.	2	3	4	3.9 in.
	(158 mm)	2	3	4	3.9 in.
					(99 mm)
	1
	6
					7.5 in.
					(191 mm)
54.7 in.
(1389 mm)	11				8	7
	11

50.5 in.
(1283 mm)		1.4 in.
		(36 mm)
	28.4 in.				6.5 in.
	(721 mm)				6.5 in.
	(721 mm)				(165 mm)
					(165 mm)
	6.5 in.
	(165 mm)		10			9
			10
		4.1 in.		4.1 in.		CFS471N
		4.1 in.		(104 mm)
		(104 mm)		(104 mm)	CFS471N
					CFS471N

4 in.

(102 mm)

CFS470N

CFS470N

		55 MODEL
1	Fill and Supply Ventilation	7	Electrical Power Input
2	Cold Water Inlet (Required)	8	External Supply Signal Input
3	Hot Water Inlet (Required)	9	Drain Outlet
4	Cold Water Inlet (Required)	10	Reuse Drain Outlet (Optional)
5	Flushing Supply Dispenser	11	Steam Connection Input (Optional)

6External Liquid Supply Inlets

Figure 9

20

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

9001000

Image 22

Contents Washer-Extractors Page Contents Explanation of Safety Messages Important Safety InstructionsSafety Information Safety Decals Operator Safety Introduction Model Identification100 135 165 200 Introduction Customer Service Replacement PartsNameplate Location Introduction Model Number Familiarization Guide 0001Wash Cylinder Information General Specifications Model Overall DimensionsWeight and Shipping Information Door Opening InformationBalance Detection Cylinder SpeedsCentrifugal Force Data Direct Steam Heating OptionalWeight and Shipping Information RPM Specifications and Dimensions Main Switch Electrical Power Inputs Flushing Supply Dispenser Steam Connection Input Optional 88 mm 220 mm Mm 53.07 in mm 50 mm 34 mm Model 1168 mm 1575 mm 33.6 1010 mm 305 mm 360 mm 56.5 mm Installation Recommended Minimum Clearances Model 100 135 165 200Installation Floor Load Data Model 100 135 165 200Mechanical Installation Important Drawing is not to scalePound 34 mm 22 mm 26.18 665 mm 26.77 50 mm 680 mm 30.71 780 mm 712 mm 34 mm 22 mm 30.12 765 mm 898 mm 42.52 47.24 1200 mm 40 mm 1200 mm 42.5 mm 1300 mm 33 mm 44.8 660 mm 55 mm 30.31 782 mm 45 mm Mounting Bolt Installation If Required Removing the Transport Brackets Front Rear 40 Models Drain Connection Rear of MachineModel 100 135 165 200 Minimum Drain ID Model Number of MachinesWater Connection Water Supply Information Model 100 135 165 200Electrical Installation Do not use a phase adder on any variable- speed machineCycle Phase Wire Full Load Amps Installation Electrical Connection Remote Liquid Supply ConnectionSteam Requirements Steam Heat Option Only Steam Supply Information 18-75 100/135 165/200Supply Programming Table Example Pumps 24V ~ Out-of-Balance Switch Automatic LubricatorControl Function Test Machine