Alliance Laundry Systems 135, 75, 40, 33, 100, 165, 200, 18, 55 manual 1010 mm 305 mm

Page 24

Specifications and Dimensions

		6						100: 52.4 in. (1331 mm)
								135: 59.3 in. (1506 mm)
	76.8 in.
(1951 mm)
	37.8 in.
	(960 mm)
	25.5 in.
	(648 mm)
									4 in.
	40.94 in.								(102 mm)
	40.94 in.
	(1040 mm)
	47.24 in.
	(1200 mm)	CFD511N						100: 39.76 in.
				12 in.				100: 39.76 in.
				12 in.				(1010 mm)
	9.3 in.		(305 mm)					135: 46.65 in.
	9.3 in.							135: 46.65 in.
	(2362 mm)							(1185 mm)	CFS476N
				6.9 in.
	3.5 in.		(175 mm)
	3.5 in.
	(89 mm)
	4.1 in.		4.5 in.
	4.1 in.		(114 mm)			2 in.		6.7 in.
	(104 mm)					2 in.		6.7 in.
	6.5 in.		2	3	5	(51 mm)		(170 mm)
	(165 mm)			3	5
								9.8 in.
								(249 mm)
	8.7 in.					1
	(221 mm)		4
			4					9
								9
	7							13
			12					13
	62 in.		12					8
	(1575 mm)							8
								10
	27.4 in.		8.5 in.
	27.4 in.		(216 mm)					8.5 in.
	(696 mm)							(216 mm)
					11			7.3 in.	CFS477N
					11		(185 mm)
		100 AND 135 MODELS
1	Fill and Supply Ventilation					8		Electrical Power Input
2	Cold Water Inlet (Required)					9		External Supply Signal Input
3	Hot Water Inlet (Required)					10		Drain Outlet
4	Cold Water Inlet (Required)					11		Reuse Drain Outlet (Optional)
5	Cold Water Inlet (Required)					12		Steam Connection Input (Optional)
6	Flushing Supply Dispenser					13		Service Power Disconnect
7	External Liquid Supply Inlets

Figure 11

22

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

9001000

Image 24

Contents Washer-Extractors Page Contents Explanation of Safety Messages Important Safety InstructionsSafety Information Safety Decals Operator Safety Introduction Model Identification100 135 165 200 Introduction Replacement Parts Customer ServiceNameplate Location Introduction Model Number Familiarization Guide 0001General Specifications Model Overall Dimensions Weight and Shipping InformationWash Cylinder Information Door Opening InformationCylinder Speeds Centrifugal Force DataBalance Detection Direct Steam Heating OptionalWeight and Shipping Information RPM Specifications and Dimensions Main Switch Electrical Power Inputs Flushing Supply Dispenser Steam Connection Input Optional 88 mm 220 mm Mm 53.07 in mm 50 mm 34 mm Model 1168 mm 1575 mm 33.6 1010 mm 305 mm 360 mm 56.5 mm Installation Recommended Minimum Clearances Model 100 135 165 200Installation Floor Load Data Model 100 135 165 200Mechanical Installation Important Drawing is not to scalePound 34 mm 22 mm 26.18 665 mm 26.77 50 mm 680 mm 30.71 780 mm 712 mm 34 mm 22 mm 30.12 765 mm 898 mm 42.52 47.24 1200 mm 40 mm 1200 mm 42.5 mm 1300 mm 33 mm 44.8 660 mm 55 mm 30.31 782 mm 45 mm Mounting Bolt Installation If Required Removing the Transport Brackets Front Rear 40 Models Drain Connection Rear of MachineModel 100 135 165 200 Minimum Drain ID Model Number of MachinesWater Connection Water Supply Information Model 100 135 165 200Electrical Installation Do not use a phase adder on any variable- speed machineCycle Phase Wire Full Load Amps Installation Electrical Connection Remote Liquid Supply ConnectionSteam Requirements Steam Heat Option Only Steam Supply Information 18-75 100/135 165/200Supply Programming Table Example Pumps 24V ~ Out-of-Balance Switch Automatic LubricatorControl Function Test Machine