Alliance Laundry Systems 165, 75, 40, 33, 100, 135, 200, 18, 55 manual 360 mm

Page 25

Specifications and Dimensions

		6						63.8 in.
		6						(1620 mm)
	82.7 in.
	(2100 mm)
	40.2 in.
	(1020 mm)
	25.25 in.
	(641 mm)
									4 in.
	44.9 in.								(102 mm)
	(1140 mm)
	51.2 in.
	(1300 mm)	CFD511N
		CFD511N
				14.25 in.
	10.75 in.			(360 mm)				46.7 in.
	10.75 in.							46.7 in.
	(273 mm)							(1185 mm)	CFD15N
				7.8 in.					CFD15N
				(198 mm)					CFD15N
	4.8 in.			(198 mm)
	4.8 in.
	(122 mm)			4.5 in.
	4.5 in.			4.5 in.
	4.5 in.		(114 mm)
	(114 mm)		(114 mm)			2 in.		7.75 in.
	6.75 in.		2	3	(51 mm)			(197 mm)
	(172 mm)			3	5
								10.24 in.
								(260 mm)
	8.7 in.				1
	(221 mm)	4
		4						9
								9
	7							13
		12						13
	73 in.	12						8
	73 in.							8
	(1854 mm)
								10
	27.4 in.			10 in.
	27.4 in.		(254 mm)					10 in.
	(696 mm)							(254 mm)
				11			9.3 in.	CFS477N
						(236 mm)
		165 MODEL
1	Fill and Supply Ventilation					8	Electrical Power Input
2	Cold Water Inlet (Required)					9	External Supply Signal Input
3	Hot Water Inlet (Required)					10	Drain Outlet (Standard)
4	Cold Water Inlet (Required)					11	Dual Drain Outlet (Optional)
5	Cold Water Inlet (Required)					12	Steam Connection Input (Optional)
6	Flushing Supply Dispenser					13	Service Power Disconnect
7	External Liquid Supply Inlets

Figure 12

9001000

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

23

Image 25

Contents Washer-Extractors Page Contents Important Safety Instructions Explanation of Safety MessagesSafety Information Safety Decals Operator Safety Model Identification Introduction100 135 165 200 Introduction Customer Service Replacement PartsNameplate Location 0001 Introduction Model Number Familiarization GuideWeight and Shipping Information General Specifications Model Overall DimensionsWash Cylinder Information Door Opening InformationCentrifugal Force Data Cylinder SpeedsBalance Detection Direct Steam Heating OptionalWeight and Shipping Information RPM Specifications and Dimensions Main Switch Electrical Power Inputs Flushing Supply Dispenser Steam Connection Input Optional 88 mm 220 mm Mm 53.07 in mm 50 mm 34 mm Model 1168 mm 1575 mm 33.6 1010 mm 305 mm 360 mm 56.5 mm Recommended Minimum Clearances Model 100 135 165 200 InstallationFloor Load Data Model 100 135 165 200 InstallationImportant Drawing is not to scale Mechanical InstallationPound 34 mm 22 mm 26.18 665 mm 26.77 50 mm 680 mm 30.71 780 mm 712 mm 34 mm 22 mm 30.12 765 mm 898 mm 42.52 47.24 1200 mm 40 mm 1200 mm 42.5 mm 1300 mm 33 mm 44.8 660 mm 55 mm 30.31 782 mm 45 mm Mounting Bolt Installation If Required Removing the Transport Brackets Front Rear 40 Models Rear of Machine Drain ConnectionMinimum Drain ID Model Number of Machines Model 100 135 165 200Water Supply Information Model 100 135 165 200 Water ConnectionDo not use a phase adder on any variable- speed machine Electrical InstallationCycle Phase Wire Full Load Amps Installation Remote Liquid Supply Connection Electrical ConnectionSteam Supply Information 18-75 100/135 165/200 Steam Requirements Steam Heat Option OnlySupply Programming Table Example Pumps 24V ~ Automatic Lubricator Out-of-Balance SwitchMachine Control Function Test