Alliance Laundry Systems 55, 75, 40, 33, 100, 135, 165, 200, 18 manual Electrical Installation

Page 49

Electrical Installation

WARNING

Hazardous Voltage. Can cause shock, burn or cause death. Allow machine power to remain off for two minutes prior to working in and around AC inverter drive.

W359

WARNING

Hazardous Voltage. Can cause shock, burn or death. Verify that a ground wire from a proven earth ground is connected to the lug near the input power block on this machine.

W360

The AC inverter drive requires a clean power supply free from voltage spikes and surges. A voltage monitor should be used to check incoming power. The customer’s local power company may provide such a monitor.

If input voltage measures above 240V for a 220V drive or above 480V for a 400V drive, ask the power company to lower the voltage. As an alternative, a step-down transformer kit is available from the distributor.

The AC drive provides overload protection for the drive motor. However, a separate single or three phase circuit breaker must be installed for complete electrical overload protection. This prevents damage to the motor by disconnecting all legs if one should be lost accidentally. Check the data plate on the back of the washer-extractor or consult Table 6 for circuit breaker requirements.

IMPORTANT: Do NOT use fuses in place of a circuit breaker.

Installation

DANGER

Do not use a phase adder on any variable- speed machine.

W490

The washer-extractor should be connected to an individual branch circuit not shared with lighting or other equipment.

The connection should be shielded in a liquid tight or approved flexible conduit with proper conductors of correct size installed in accordance with the National Electric Code or other applicable codes. The connection must be made by a qualified electrician using the wiring diagram provided with the washer- extractor, or according to accepted European standards for CE-approved equipment.

Use wire sizes indicated in Table 6 for runs up to 50 feet.

Use next larger size for runs of 50 to 100 feet. Use two sizes larger for runs greater than 100 feet.

For personal safety and proper operation, the washer- extractor must be grounded in accordance with state and local codes. If such codes are not available, grounding must conform with the National Electric Code, article 250-95. The ground connection must be made to a proven earth ground, not to conduit or water pipes.

IMPORTANT: Alliance Laundry Systems Warranty does not cover components that fail as a result of improper input voltage.

9001000

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

47

Page 48 Page 50
Image 49
Page 48 Page 50
Contents Washer-Extractors Page Contents Important Safety Instructions Explanation of Safety MessagesSafety Information Safety Decals Operator Safety Model Identification Introduction100 135 165 200 Introduction Customer Service Replacement PartsNameplate Location 0001 Introduction Model Number Familiarization GuideWeight and Shipping Information General Specifications Model Overall DimensionsWash Cylinder Information Door Opening InformationCentrifugal Force Data Cylinder SpeedsBalance Detection Direct Steam Heating OptionalWeight and Shipping Information RPM Specifications and Dimensions Main Switch Electrical Power Inputs Flushing Supply Dispenser Steam Connection Input Optional 88 mm 220 mm Mm 53.07 in mm 50 mm 34 mm Model 1168 mm 1575 mm 33.6 1010 mm 305 mm 360 mm 56.5 mm Recommended Minimum Clearances Model 100 135 165 200 InstallationFloor Load Data Model 100 135 165 200 InstallationImportant Drawing is not to scale Mechanical InstallationPound 34 mm 22 mm 26.18 665 mm 26.77 50 mm 680 mm 30.71 780 mm 712 mm 34 mm 22 mm 30.12 765 mm 898 mm 42.52 47.24 1200 mm 40 mm 1200 mm 42.5 mm 1300 mm 33 mm 44.8 660 mm 55 mm 30.31 782 mm 45 mm Mounting Bolt Installation If Required Removing the Transport Brackets Front Rear 40 Models Rear of Machine Drain ConnectionMinimum Drain ID Model Number of Machines Model 100 135 165 200Water Supply Information Model 100 135 165 200 Water ConnectionDo not use a phase adder on any variable- speed machine Electrical InstallationCycle Phase Wire Full Load Amps Installation Remote Liquid Supply Connection Electrical ConnectionSteam Supply Information 18-75 100/135 165/200 Steam Requirements Steam Heat Option OnlySupply Programming Table Example Pumps 24V ~ Automatic Lubricator Out-of-Balance SwitchMachine Control Function Test
Top Page Image Contents