Alliance Laundry Systems 135, 75, 40 Explanation of Safety Messages, Important Safety Instructions

Page 4

Safety Information

Explanation of Safety Messages

Precautionary statements (“DANGER,” “WARNING,” and “CAUTION”), followed by specific instructions, are found in this manual and on machine decals. These precautions are intended for the personal safety of the operator, user, servicer, and those maintaining the machine.

DANGER

DANGER indicates the presence of a hazard that will cause severe personal injury, death, or substantial property damage if the danger is ignored.

WARNING

WARNING indicates the presence of a hazard that can cause severe personal injury, death, or substantial property damage if the warning is ignored.

CAUTION

CAUTION indicates the presence of a hazard that will or can cause minor personal injury or property damage if the caution is ignored.

Additional precautionary statements (“IMPORTANT” and “NOTE”) are followed by specific instructions.

IMPORTANT: The word “IMPORTANT” is used to inform the reader of specific procedures where minor machine damage will occur if the procedure is not followed.

NOTE: The word “NOTE” is used to communicate installation, operation, maintenance or servicing information that is important but not hazard related.

Important Safety Instructions

WARNING

To reduce the risk of fire, electric shock, serious injury or death to persons when using your washer, follow these basic precautions:

W023

1.Read all instructions before using the washer.

2.Refer to the GROUNDING INSTRUCTIONS in the INSTALLATION manual for the proper grounding of the washer.

3.Do not wash textiles that have been previously cleaned in, washed in, soaked in, or spotted with gasoline, kerosene, waxes, cooking oils, dry- cleaning solvents, or other flammable or explosive substances as they give off vapors that could ignite or explode.

4.Do not add gasoline, dry-cleaning solvents, or other flammable or explosive substances to the wash water. These substances give off vapors that could ignite or explode.

5.Under certain conditions, hydrogen gas may be produced in a hot water system that has not been used for two weeks or more. HYDROGEN GAS IS EXPLOSIVE. If the hot water system has not been used for such a period, before using a washing machine or combination washer-dryer, turn on all hot water faucets and let the water flow from each for several minutes. This will release any accumulated hydrogen gas. The gas is flammable, do not smoke or use an open flame during this time.

6.Do not allow children to play on or in the washer. Close supervision of children is necessary when the washer is used near children. This is a safety rule for all appliances.

7.Before the washer is removed from service or discarded, remove the door to the washing compartment.

8.Do not reach into the washer if the wash drum is moving.

2

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

9001000

Image 4
Contents Washer-Extractors Page Contents Explanation of Safety Messages Important Safety InstructionsSafety Information Safety Decals Operator Safety Introduction Model Identification100 135 165 200 Introduction Customer Service Replacement PartsNameplate Location Introduction Model Number Familiarization Guide 0001General Specifications Model Overall Dimensions Weight and Shipping InformationWash Cylinder Information Door Opening InformationCylinder Speeds Centrifugal Force DataBalance Detection Direct Steam Heating OptionalWeight and Shipping Information RPM Specifications and Dimensions Main Switch Electrical Power Inputs Flushing Supply Dispenser Steam Connection Input Optional 88 mm 220 mm Mm 53.07 in mm 50 mm 34 mm Model 1168 mm 1575 mm 33.6 1010 mm 305 mm 360 mm 56.5 mm Installation Recommended Minimum Clearances Model 100 135 165 200Installation Floor Load Data Model 100 135 165 200Mechanical Installation Important Drawing is not to scalePound 34 mm 22 mm 26.18 665 mm 26.77 50 mm 680 mm 30.71 780 mm 712 mm 34 mm 22 mm 30.12 765 mm 898 mm 42.52 47.24 1200 mm 40 mm 1200 mm 42.5 mm 1300 mm 33 mm 44.8 660 mm 55 mm 30.31 782 mm 45 mm Mounting Bolt Installation If Required Removing the Transport Brackets Front Rear 40 Models Drain Connection Rear of MachineModel 100 135 165 200 Minimum Drain ID Model Number of MachinesWater Connection Water Supply Information Model 100 135 165 200Electrical Installation Do not use a phase adder on any variable- speed machineCycle Phase Wire Full Load Amps Installation Electrical Connection Remote Liquid Supply ConnectionSteam Requirements Steam Heat Option Only Steam Supply Information 18-75 100/135 165/200Supply Programming Table Example Pumps 24V ~ Out-of-Balance Switch Automatic LubricatorControl Function Test Machine