Alliance Laundry Systems 18, 75, 40, 33, 55 manual Installation, Floor Load Data Model 100 135 165 200

Page 28

Installation

Machine Foundation

Thoroughness of detail must be stressed with all foundation work to ensure a stable unit installation, eliminating possibilities of excessive vibration during extract.

CAUTION

Ensure that the machine is installed on a level floor of sufficient strength and that the recommended clearances for inspection and maintenance are provided. Never allow the inspection and maintenance space to be blocked.

W488

The washer-extractor must be placed on a smooth level surface so that the entire base of the machine is supported and rests on the mounting surface.

The standard installation does not require anchoring unless mandated by state or local codes.

Static and dynamic loads on the floor or foundation are shown in Table 2.

Table 2 can be used as a reference when designing floors and foundations.

IMPORTANT: Mounting bolts MUST be used for installation on the 18, 25 and 35 models equipped with steam heat and models installed on metal base frames. Refer to Mounting Bolt Installation.

Floor Load Data

Model

18

25

33

35

40

55

75

100

135

165

200

 

 

 

 

 

 

 

 

 

 

 

 

Kinetic Energy of the

1386

1730

2736

3240

4105

6640

12404

18361

23257

29581

29581

Cylinder, (N/m)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Dynamic Bottom

700/16

750/16

1200/16

1200/16

1200/16

1700/15

2000/15

2960/13

3900/13

4960/13

6100/13

Load, (N/Hz)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Table 2

 

 

 

 

 

 

26

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

9001000

Image 28
Contents Washer-Extractors Page Contents Explanation of Safety Messages Important Safety InstructionsSafety Information Safety Decals Operator Safety Introduction Model Identification100 135 165 200 Introduction Customer Service Replacement PartsNameplate Location Introduction Model Number Familiarization Guide 0001General Specifications Model Overall Dimensions Weight and Shipping InformationWash Cylinder Information Door Opening InformationCylinder Speeds Centrifugal Force DataBalance Detection Direct Steam Heating OptionalWeight and Shipping Information RPM Specifications and Dimensions Main Switch Electrical Power Inputs Flushing Supply Dispenser Steam Connection Input Optional 88 mm 220 mm Mm 53.07 in mm 50 mm 34 mm Model 1168 mm 1575 mm 33.6 1010 mm 305 mm 360 mm 56.5 mm Installation Recommended Minimum Clearances Model 100 135 165 200Installation Floor Load Data Model 100 135 165 200Mechanical Installation Important Drawing is not to scalePound 34 mm 22 mm 26.18 665 mm 26.77 50 mm 680 mm 30.71 780 mm 712 mm 34 mm 22 mm 30.12 765 mm 898 mm 42.52 47.24 1200 mm 40 mm 1200 mm 42.5 mm 1300 mm 33 mm 44.8 660 mm 55 mm 30.31 782 mm 45 mm Mounting Bolt Installation If Required Removing the Transport Brackets Front Rear 40 Models Drain Connection Rear of MachineModel 100 135 165 200 Minimum Drain ID Model Number of MachinesWater Connection Water Supply Information Model 100 135 165 200Electrical Installation Do not use a phase adder on any variable- speed machineCycle Phase Wire Full Load Amps Installation Electrical Connection Remote Liquid Supply ConnectionSteam Requirements Steam Heat Option Only Steam Supply Information 18-75 100/135 165/200Supply Programming Table Example Pumps 24V ~ Out-of-Balance Switch Automatic LubricatorControl Function Test Machine