Alliance Laundry Systems 75, 40, 33, 100, 135, 165, 200, 18, 55 manual 56.5 mm

Page 26

Specifications and Dimensions

				6
										2.23 in.
										(56.5 mm)
82.7 in.
(2100 mm)
	39 in.
	(993 mm)
	23.75 in.
	(603 mm)						1.73 in.			1.73 in.
							1.73 in.	53.74 in.		1.73 in.
							(44 mm)	(1365 mm)	57.2 in.	(44 mm)
							10.71 in.		57.2 in.	1.04 in.
	3.19 in.	44.8 in.		3.19 in.			(272 mm)	68.96 in.	(1453 mm)	(26.5 mm)
	3.19 in.	44.8 in.		3.19 in.
	(81 mm)	(1138 mm)		(81 mm)
	(81 mm)	(1138 mm)		(81 mm)				(175.2 mm)
		51.18 in.						(175.2 mm)
		51.18 in.
		(1300 mm)		CFD533N						CFD534N
				CFD533N						CFD534N
		16.06 in.
		(408 mm)
		12.72 in.
		(323 mm)
		9.76 in.
		(248 mm)						10.12 in.
		6.81 in.					6.67 in.	10.12 in.
		6.81 in.					6.67 in.	(257 mm)
		(173 mm)		2	3	(169.5 mm)		(257 mm)
		(173 mm)				(169.5 mm)

								19.13 in.
		10.31 in.						(486 mm)
		10.31 in.			5
		(262 mm)			5
		9.33 in.	7	4
		(237 mm)	7	4	1			9
		6.97 in.			1			9
		(117 mm)						13
		4.61 in.						13
		(117 mm)						8
		3.19 in.
		(81 mm)
					12			10
					12
		35.37 in.
		(899.5)
								6.85 in.
								(174 mm)
		10.24 in.			11			10.24 in.
		(260 mm)			11			(260 mm)
								CFD535N
				200 MODEL
1	Fill and Supply Ventilation						8	Electrical Power Input
2	Cold Water Inlet (Required)						9	External Supply Signal Input
3	Hot Water Inlet (Required)						10	Drain Outlet (Standard)
4	Cold Water Inlet (Required)						11	Dual Drain Outlet (Optional)
5	Cold Water Inlet (Required)						12	Steam Connection Input (Optional)
6	Flushing Supply Dispenser						13	Service Power Disconnect
7	External Liquid Supply Inlets

Figure 13

24

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

9001000

Image 26

Contents Washer-Extractors Page Contents Explanation of Safety Messages Important Safety InstructionsSafety Information Safety Decals Operator Safety Introduction Model Identification100 135 165 200 Introduction Nameplate Location Replacement PartsCustomer Service Introduction Model Number Familiarization Guide 0001Wash Cylinder Information General Specifications Model Overall DimensionsWeight and Shipping Information Door Opening InformationBalance Detection Cylinder SpeedsCentrifugal Force Data Direct Steam Heating OptionalWeight and Shipping Information RPM Specifications and Dimensions Main Switch Electrical Power Inputs Flushing Supply Dispenser Steam Connection Input Optional 88 mm 220 mm Mm 53.07 in mm 50 mm 34 mm Model 1168 mm 1575 mm 33.6 1010 mm 305 mm 360 mm 56.5 mm Installation Recommended Minimum Clearances Model 100 135 165 200Installation Floor Load Data Model 100 135 165 200Mechanical Installation Important Drawing is not to scalePound 34 mm 22 mm 26.18 665 mm 26.77 50 mm 680 mm 30.71 780 mm 712 mm 34 mm 22 mm 30.12 765 mm 898 mm 42.52 47.24 1200 mm 40 mm 1200 mm 42.5 mm 1300 mm 33 mm 44.8 660 mm 55 mm 30.31 782 mm 45 mm Mounting Bolt Installation If Required Removing the Transport Brackets Front Rear 40 Models Drain Connection Rear of MachineModel 100 135 165 200 Minimum Drain ID Model Number of MachinesWater Connection Water Supply Information Model 100 135 165 200Electrical Installation Do not use a phase adder on any variable- speed machineCycle Phase Wire Full Load Amps Installation Electrical Connection Remote Liquid Supply ConnectionSteam Requirements Steam Heat Option Only Steam Supply Information 18-75 100/135 165/200Supply Programming Table Example Pumps 24V ~ Out-of-Balance Switch Automatic LubricatorControl Function Test Machine