Are both the hot and cold water faucets turned on?
Turn on the water.
Is the water inlet hose kinked? Straighten the hoses.
Does the water level seem too low, or does the washer appear to not fill completely? The top of the agitator is much higher than the highest water level. This is normal and necessary for clothes to move freely.
Has a fuse blown, or has a circuit breaker tripped? Replace the fuse, or reset the circuit breaker. If the problem continues, call an electrician.
Is the washer in a normal pause in the cycle? The washer pauses for about 2 minutes during certain cycles. Allow the cycle to continue. Some cycles feature periods of agitation and soak.
Is the washer overloaded? Wash smaller loads.
Is the lid open? The lid must be closed during operation. Washer will not agitate or spin with the lid open. On models with Auto Load Sensing, water fill will not begin with the lid open.
Washer continues to fill or drain, cycle seems stuck
Is the top of drain hose lower than the control knobs on washer? The top of the drain hose must be at least 39" (99 cm) above the floor. See “Drain System” in the Installation Instructions.
Does the drain hose fit too tightly in the standpipe, or is it taped to the standpipe? The drain hose should be loose yet fit securely. Do not seal the drain hose with tape. The hose needs an air gap. See “Secure the Drain Hose” in the Installation Instructions.
Washer won’t drain or spin, water remains in washer
Is the drain hose clogged, or the end of the drain hose more than 96" (244 cm) above the floor? See “Drain System” in the Installation Instructions.
Is the lid open? The lid must be closed during operation. Washer will not agitate or spin with the lid open.
Is there excessive sudsing? Always measure detergent. Follow manufacturer’s directions. If you have very soft water, you might need to use less detergent.
Wash/Rinse temperature
Are the hot and cold water inlet hoses reversed? See “Connect the Inlet Hoses” in the Installation Instructions.
Are you washing many loads? As your frequency of loads washed increases, the water temperature may decrease for hot and warm temperatures. This is normal.
Did you select a Warm/Warm temperature setting? On models without AUTO TEMPERATURE CONTROL (ATC) that do have a Warm/Warm temperature selection, the warm wash will be followed by an energy saving cold rinse followed by warm spray rinses. This saves energy while providing the same rinse performance.
Do you have an ENERGY STAR washer? The wash water temperatures may feel cooler to you than those of your previous washer. This is normal.
Clothing Care
Load too wet
Did you use the right cycle for the load being washed? Select a cycle with a higher spin speed (if available).
Did you wash an extra large load? A large unbalanced load could result in a reduced spin speed and wet clothes at the end of the cycle. Evenly distribute the load and make sure the height of the load does not exceed the top row of basket holes.
Residue or lint on load
Did you sort properly? Sort lint givers (towels, chenille) from lint takers (corduroy, synthetics). Also sort by color.
Did you overload the washer? The wash load must be balanced and not overloaded. Clothes should move freely. Lint or powdered detergent can be trapped in the load if overloaded. Wash smaller loads.
Did you select the correct water level? The water level should be correct for the load size. The load should be under water.
Did you use enough detergent? Follow manufacturer’s directions. Use enough detergent to hold the lint in the water.
Did you line dry your clothing? If so, you can expect some lint on the clothing. The air movement and tumbling of a dryer removes lint from the load.
Was paper or tissue left in the pockets?
Is your water colder than 60°F (15.6°C)? Wash water colder than 60°F (15.6°C) may not completely dissolve the detergent.
Did you use the proper cycle time and agitation speed for the load? Reducing wash time (duration) and agitation speed are ways to reduce lint.
Did you select the 2nd Rinse option (on some models)? A second rinse may reduce residue or lint on the load.
Load is wrinkled, twisted, or tangled
Did you unload the washer promptly? Unload the washer as soon as it stops.
Did you use the right cycle for the load being washed? Use cycles with shorter wash times and low wash and spin speeds (if available) to reduce wrinkling, tangling, and twisting.
Did you overload the washer? The wash load must be balanced and not overloaded. Loads should move freely during washing to reduce wrinkling, tangling, and twisting.
Was the wash water warm enough to relax wrinkles? If safe for the load, use warm or hot wash water. Use cold rinse water.
Are the hot and cold water hoses reversed? Check to be sure the hot and cold water hoses are connected to the right faucets. A hot rinse followed by spin will cause wrinkling. See “Connect the Inlet Hoses” in the Installation Instructions.
Did you wrap items around the agitator? Drop items loosely into the washer. Do not wrap items around the agitator.
8