Whirlpool GVW9959K-0 manual Water Inlet and Dispenser VALVE, Operating PS Test

Page 55

WATER INLET AND DISPENSER VALVE, OPERATING PS TEST

If Operating Pressure Switch trips at any time, all water valves should turn off. Press EXTRA RINSE to start draining after key press #5 to start draining. Press EXTRA RINSE again to turn off the pump.

1

2

PRESS TOUCHPAD	DISPLAY	CONTROL ACTION
SOAK		Key Dance key press #1
CYCLE SIGNAL		Key Dance key press #2

3	SOAK	Key Dance key press #3
4	CYCLE SIGNAL	Key Dance key press #4
		Presses #1 - #4 must be completed in 5 seconds or the key
		dance is not valid.
5	WATER TEMP	Key press #5, “00” on the display
6	WATER TEMP	Cold Water Inlet Valve and Fabric Softener dispenser valve
		on. Cold/Cold and Normal (above SOIL LEVEL) LEDs will
		turn on.
7	SOIL LEVEL	Normal LED will turn off and Heavy LED will turn on. Fabric
		softener valve will shut off and Fresh water valve will turn on.
8	SOIL LEVEL	Heavy LED will turn off and Refresh will turn on. Fresh water
		valve will turn off and Detergent dispenser valve will turn on.
9	SOIL LEVEL	Refresh LED will turn off and Light LED will turn on.
		Detergent valve will turn off and Bleach valve will turn on.
10	SOIL LEVEL	This key press turns off the Bleach and turns on the Fabric
		Softener.
11	WATER TEMP	Cold/Cold LED turns off and Hot/Cold LED turns on. Cold
		inlet valve turns off and Hot inlet valve turns on.

12

WATER TEMP

Both hot and cold inlet valves turn on.

13

WATER TEMP

All valves turn off.

14

STOP/CANCEL

All LEDs off

Cancel all diagnostics, go back to Off mode.

51

Image 55

Contents Page Introduction Table of Contents MODEL/SERIAL Number Plate Serial Number Designator SafetyModel Number Designator Model Number G V W 9 9 5 9 K Q For a permanently connected washer InstallationConsiderations Section ONETools needed Parts Supplied DrainSystem ConnectingtheDrainHose InstallationChecklist Use&CareInformation Control Panel Theory of OperationSection TWO NutationOption Descriptions Operational Cycle Default Wash and SpinSoil Level Whitest Whites Water TempAssured Water Temp ATC ThresholdsAdditional Options End of Cycle SignalMotor Controller Machine ControllerDrive Motor Leveler Peekaboo ModeUniversal Joint Drive System Interlock SwitchesShield Capacitor LOG Valve Assembly Pressure SwitchesOPR FLD Recirculation Recirculation and DrainWater Pump/Pump Motor Outer TubChanging Options after pressing Start DrainChanging Cycles and Options Changing Cycles after pressing StartOperational Cycle Notes Drive Motor Notes Pump Drive Description Water Description Water Pump Drive Duration Description Water Pump Drive Pump Drive Description Action Speed Pump Drive Description Delicate/Casual SPIN+RECIRC+FILL Wash Detergent PS Controlled Recirc Spin Garments are labelled Hand Wash because HandwashExtra Rinse Soak CycleExtend Spin Cycle Rinse & Spin When to use Rinse & SpinTo use or change Rinse & Spin settings Suds Lock Detection/CleanoutComponent Location Component AccessSpecial TOOLS/PARTS Required for Service Section ThreeElectrostatic Discharge ESD Sensitive Electronics Accessing Components in the ConsoleRemoving the Motor Control Board Removing the ConsoleRemoving Console Components Removing the Machine Control BoardRemoving the Log Valve Assembly Removing the Pressure SwitchesRaising the Washer Top to the Service Position Accessing Components Beneath the Washer TOPKet. Fig Removing Components in the Tub18b Reassembling Tub ComponentsTab Components Accessible with Front Cabinet Panel Removed Accessing Components Beneath the TUBRemoving the Front Cabinet Panel Motor mounting bracket to the motor plate Servicing Components from the Bottom of the WasherRemoving the Drive Motor Removing the Thrust Plate32 shows all the components of the thrust plate assembly Removing the Brake Assembly/Nutate ShaftReplacing the Capacitor Removing the Pump and Pump MotorReplacing the Outer Tub Troubleshooting Chart Troubleshooting and DiagnosisSection Four Motor Overheats OverfillsWon’t Nutate Won’t SpinIncorrect Water TemperatureWon’t Drain Washer VibratingLoad is Wrinkled Power FailureProcessor Reset ErrorLimit Lid Switch ErrorLong Drain Average CurrentSuds Lock Self Diagnostic RoutinesAutomatic Service Diagnostics Mode Open LidPressSOAK Cycle Signal Soak Cycle Signal Manual Diagnostic ModeRunning Nutate or Spin Nutate and Recirculate Test Pump Drain/RecirculationWater Inlet and Dispenser VALVE, Operating PS Test If a single LED does not light up Console Switches and Indicators TestIf none of the LEDs light up If a particular group of LEDs does not light upChecking Touchpad Functioning KEY Switch MatrixChecking Drive and Pump Motor Continuity Sales Demo Mode120VAC Electrical Supply Troubleshooting TestsWater Inlet and Dispenser Solenoid Test Machine Control Relay Motor and Motor Control System TestMotor Controller Drive Motor and Wiring Harness Automatic Temperature Control TestIf the fill valves are working properly Drain/Recirculation Test Operating and Over Fill Pressure Switch TestPage Page Tech Tips Wiring DiagramSection Five Warranty Information Component Resistance ChartUnited States Rprt