Whirlpool GVW9959K-0 manual Leveler, Peekaboo Mode

Page 16

Peekaboo Mode

The Peekaboo mode allows the user the opportunity to look into the washer during a wash action. During the Peekaboo Mode, the electronic control will allow the machine to nutate at 150 NPM for a maximum of 5-seconds after the washer lid is opened. When the lid is closed, the Start pad must be pressed to continue the cycle.

NUTATION

The Calypso washer achieves a significant en- ergy savings by utilizing less water than a tradi- tional top loading machine with an agitator. This is made possible by the use of a Wash Plate which provides an undulating motion to toss the wash load. This action is called nutation.

The wash plate is tipped at approximately 35 de- grees from level. The undulating action constantly rolls the load over and moving in a circular mo- tion.

The water in the basket is constantly recirculated and sprayed onto the wash load during wash and rinse cycles.

Water is Sprayed

on Wash Load

From Here

Wash Plate

Fig. 2-4

LEVELER

Nutate Action

The leveler acts as the mechanism that tilts the nutate or outer wash plate from a level to a 35 degree tilted position. The leveler is driven by the nutate shaft which replaces the traditional agitator shaft. A shifting mechanism on the underside of the leveler moves it from a perpendicular alignment in the spin mode to the 35 degree tilt required for nutation.

Leveler

Note position of

hub tab

Shift Mechanism

(Nutate Position)

Nutate Shaft

Leveler in nutate position.

Fig. 2-5

12

Image 16
Contents Page Introduction Table of Contents MODEL/SERIAL Number Plate Serial Number Designator SafetyModel Number Designator Model Number G V W 9 9 5 9 K Q Installation ConsiderationsSection ONE For a permanently connected washerTools needed Parts Supplied DrainSystem ConnectingtheDrainHose InstallationChecklist Use&CareInformation Theory of Operation Section TWONutation Control PanelOption Descriptions Operational Cycle Default Wash and SpinSoil Level Water Temp Assured Water TempATC Thresholds Whitest WhitesEnd of Cycle Signal Additional OptionsMotor Controller Machine ControllerDrive Motor Peekaboo Mode LevelerUniversal Joint Drive System Interlock SwitchesShield Capacitor LOG Valve Assembly Pressure SwitchesOPR FLD Recirculation and Drain Water Pump/Pump MotorOuter Tub RecirculationDrain Changing Cycles and OptionsChanging Cycles after pressing Start Changing Options after pressing StartOperational Cycle Notes Drive Motor Notes Pump Drive Description Water Description Water Pump Drive Duration Description Water Pump Drive Pump Drive Description Action Speed Pump Drive Description Delicate/Casual SPIN+RECIRC+FILL Wash Detergent PS Controlled Recirc Spin Handwash Garments are labelled Hand Wash becauseExtra Rinse Soak CycleExtend Spin Cycle When to use Rinse & Spin To use or change Rinse & Spin settingsSuds Lock Detection/Cleanout Rinse & SpinComponent Access Special TOOLS/PARTS Required for ServiceSection Three Component LocationAccessing Components in the Console Electrostatic Discharge ESD Sensitive ElectronicsRemoving the Console Removing Console ComponentsRemoving the Machine Control Board Removing the Motor Control BoardRemoving the Pressure Switches Removing the Log Valve AssemblyAccessing Components Beneath the Washer TOP Raising the Washer Top to the Service PositionRemoving Components in the Tub Ket. FigReassembling Tub Components 18bTab Components Accessible with Front Cabinet Panel Removed Accessing Components Beneath the TUBRemoving the Front Cabinet Panel Servicing Components from the Bottom of the Washer Removing the Drive MotorRemoving the Thrust Plate Motor mounting bracket to the motor plateRemoving the Brake Assembly/Nutate Shaft 32 shows all the components of the thrust plate assemblyReplacing the Capacitor Removing the Pump and Pump MotorReplacing the Outer Tub Troubleshooting Chart Troubleshooting and DiagnosisSection Four Overfills Won’t NutateWon’t Spin Motor OverheatsTemperature Won’t DrainWasher Vibrating Incorrect WaterPower Failure Processor ResetError Load is WrinkledLid Switch Error Long DrainAverage Current LimitSelf Diagnostic Routines Automatic Service Diagnostics ModeOpen Lid Suds LockPressSOAK Cycle Signal Soak Cycle Signal Manual Diagnostic ModeRunning Nutate or Spin Pump Drain/Recirculation Nutate and Recirculate TestWater Inlet and Dispenser VALVE, Operating PS Test Console Switches and Indicators Test If none of the LEDs light upIf a particular group of LEDs does not light up If a single LED does not light upKEY Switch Matrix Checking Touchpad FunctioningSales Demo Mode Checking Drive and Pump Motor Continuity120VAC Electrical Supply Troubleshooting TestsWater Inlet and Dispenser Solenoid Test Machine Control Relay Motor and Motor Control System TestMotor Controller Drive Motor and Wiring Harness Automatic Temperature Control TestIf the fill valves are working properly Operating and Over Fill Pressure Switch Test Drain/Recirculation TestPage Page Tech Tips Wiring DiagramSection Five Component Resistance Chart Warranty InformationUnited States Rprt