Whirlpool GVW9959K-0 Operational Cycle Default Wash and Spin, Option Descriptions, Soil Level

Page 12

OPERATIONAL CYCLE DEFAULT WASH AND SPIN

	MAIN WASH ACTION	FINAL SPIN

CYCLES

Whitest Whites	275 NPM nutate	800 RPM
Heavy Duty	300 NPM nutate	800 RPM
Normal	275 NPM nutate	800 RPM
Jeans/Darks	250 NPM nutate	800 RPM
Bulky Items	250 NPM nutate	400 RPM
Quick Wash	250 NPM nutate	800 RPM
Delicate Casual	60 RPM spin and spray wash	400 RPM
Wool	60 RPM spin and spray wash	300 RPM
Hand Wash	60 RPM spin and spray wash	400 RPM
Rinse & Spin	N/A-not a wash	800 RPM
Extend Spin	N/A-not a wash	800 RPM

NOTE: NPM = Nutations per minute

RPM = Revolutions per minute

OPTION DESCRIPTIONS

Soil Level

Soil Level adjusts the amount of nutation or spray wash time in the selected cycle. It is valid for all cycles except Extend Spin and Rinse & Spin stand-alone cycles. Soil Level changes the 7-segment display in 1-minute increments, looping back to the minimum time once the maximum time has been reached. The following table shows the time display in the 7-segment display for a given cycle and soil level. These are total estimated times for the entire cycle.

SOIL LEVEL	EX HEAVY	HEAVY	NORMAL	LIGHT	REFRESH

CYCLE
Whitest Whites	51	50	49	48	47
Heavy Duty	53	52	51	50	49
Normal	46	45	44	43	42
Jeans/Darks	46	45	44	43	42
Bulky Items	46	45	44	43	42
Quick Wash	27	26	25	24	23
Delicate Casual	40	39	38	37	36
Wool	32	31	30	29	28
Hand Wash	34	33	32	31	30

= Default

8

Image 12

Contents Page Introduction Table of Contents Safety MODEL/SERIAL Number Plate Serial Number DesignatorModel Number Designator Model Number G V W 9 9 5 9 K Q Installation ConsiderationsSection ONE For a permanently connected washerTools needed Parts Supplied DrainSystem ConnectingtheDrainHose InstallationChecklist Use&CareInformation Theory of Operation Section TWONutation Control PanelOperational Cycle Default Wash and Spin Option DescriptionsSoil Level Water Temp Assured Water TempATC Thresholds Whitest WhitesEnd of Cycle Signal Additional OptionsMachine Controller Motor ControllerDrive Motor Peekaboo Mode LevelerUniversal Joint Interlock Switches Drive SystemShield Capacitor Pressure Switches LOG Valve AssemblyOPR FLD Recirculation and Drain Water Pump/Pump MotorOuter Tub RecirculationDrain Changing Cycles and OptionsChanging Cycles after pressing Start Changing Options after pressing StartOperational Cycle Notes Drive Motor Notes Pump Drive Description Water Description Water Pump Drive Duration Description Water Pump Drive Pump Drive Description Action Speed Pump Drive Description Delicate/Casual SPIN+RECIRC+FILL Wash Detergent PS Controlled Recirc Spin Handwash Garments are labelled Hand Wash becauseSoak Cycle Extra RinseExtend Spin Cycle When to use Rinse & Spin To use or change Rinse & Spin settingsSuds Lock Detection/Cleanout Rinse & SpinComponent Access Special TOOLS/PARTS Required for ServiceSection Three Component LocationAccessing Components in the Console Electrostatic Discharge ESD Sensitive ElectronicsRemoving the Console Removing Console ComponentsRemoving the Machine Control Board Removing the Motor Control BoardRemoving the Pressure Switches Removing the Log Valve AssemblyAccessing Components Beneath the Washer TOP Raising the Washer Top to the Service PositionRemoving Components in the Tub Ket. FigReassembling Tub Components 18bTab Accessing Components Beneath the TUB Components Accessible with Front Cabinet Panel RemovedRemoving the Front Cabinet Panel Servicing Components from the Bottom of the Washer Removing the Drive MotorRemoving the Thrust Plate Motor mounting bracket to the motor plateRemoving the Brake Assembly/Nutate Shaft 32 shows all the components of the thrust plate assemblyRemoving the Pump and Pump Motor Replacing the CapacitorReplacing the Outer Tub Troubleshooting and Diagnosis Troubleshooting ChartSection Four Overfills Won’t NutateWon’t Spin Motor OverheatsTemperature Won’t DrainWasher Vibrating Incorrect WaterPower Failure Processor ResetError Load is WrinkledLid Switch Error Long DrainAverage Current LimitSelf Diagnostic Routines Automatic Service Diagnostics ModeOpen Lid Suds LockManual Diagnostic Mode PressSOAK Cycle Signal Soak Cycle SignalRunning Nutate or Spin Pump Drain/Recirculation Nutate and Recirculate TestWater Inlet and Dispenser VALVE, Operating PS Test Console Switches and Indicators Test If none of the LEDs light upIf a particular group of LEDs does not light up If a single LED does not light upKEY Switch Matrix Checking Touchpad FunctioningSales Demo Mode Checking Drive and Pump Motor ContinuityTroubleshooting Tests 120VAC Electrical SupplyWater Inlet and Dispenser Solenoid Test Motor and Motor Control System Test Machine Control RelayMotor Controller Automatic Temperature Control Test Drive Motor and Wiring HarnessIf the fill valves are working properly Operating and Over Fill Pressure Switch Test Drain/Recirculation TestPage Page Wiring Diagram Tech TipsSection Five Component Resistance Chart Warranty InformationUnited States Rprt