Electrolux 63742 VI manual Building-in, Preparation and assembly of the door

Page 43

Installation 43

Building-in

600

This appliance has been designed to be built into the kitchen furniture.

The recess should have the dimensions shown in picture A.

818 416 176,5

515

596

201

1 54

	600
		.
	min
0
60

820 min

A

	8	1
	8	95
		95
		160
165		90
165		490
		490

When installing the appliance into the kitchen furniture ensure, if possible, the hoses are placed in either of the two recesses on the back of the appliance. This will help to pre- vent the hoses from becoming kinked or trapped.

Preparation and assembly of the door

The machine is originally pre-arranged for the assembly of a door opening from right to left.

In this case it is sufficient to screw in the hinges (1) and the counter-magnet (6) provided with the appliance, at the right level (Fig. B).

a) Door

The dimensions of the door should be:

- width 595-598 mm - thickness 16-22 mm

The height (C-Fig. C) depends on the height of the adjacent furniture's base.

b) Hinges

		6
	1	2	7
	1	2	7
	1
			3

4

5

To mount the hinges it is necessary to drill two holes (dia. 35 mm, depth 12.5-14 mm depending on the depth of door furniture) on the inner side of the door. The distance between the holes hobs fixing centres must be 416 mm.

The distance (B) from upper edge of the door to the centre of the hole depends on the adjacent furniture's dimensions.

The required dimensions are given in the picture C.

The hinges will be fixed to the door by means of screws for wood (2-Fig. B) supplied with the appliance.

B		23	8
B
35 Ø 12.5-14 depth
1
6
	-
		22	B

416 C

1,5

22+

	-598
C	595
C

Image 43

Contents Lavamat 63742 Dear Customer Contents What to do if Technical Data Consumption value Packaging materials Old machine Ecological hints InstallationPrior to using for the first time Safety informationGeneral safety Installation Use Child SafetyProduct description Compartment for prewash phase or stain removerDetergent dispenser drawer Control panel Table of symbolsChild safety lock 10.1 10.2 Personalisation Acoustic signalsChild safety lock First UsePull out the dispenser drawer until it Daily UseLoad the laundry Measure out the detergent and the fabric softenerMachine is now switched on Select the Sensitive option Button Programme option buttonSelect the Prewash option Button Select the Stain option ButtonSelect the Time option Button Select the Delay Start ButtonSelect the START/PAUSE Button Altering an option or a running programme Select an additional rinseInterrupting a programme 10.2 go off and a blinking 0 will appear on the display Cancelling a programmeOpening the door after the programme has started At the end of the programmeNon-shrink shirts Washing programmesBlouses Spin Programme information Before loading the laundry TemperaturesPreparing the wash cycle Sorting out the laundryFollowing weights are indicative Laundry weightsMaximum loads Detergents and additives Removing stainsMarked before starting the wash programme Quantity of detergent to be usedDegrees of water hardness Powder detergents for delicate fabrics 60C max and woollensCare and cleaning Door seal Washing drumDrain pump Emergency emptying out Water inlet filterFrost precautions What to do if Possible cause/SolutionMachine fills then empties immediately Cause possible/Solution Consumption value Technical DataUnpacking InstallationPolystyrene base from the bottom Six smaller bolts C Water inlet Positioning and levellingWater drainage Water-stop device Onto a sink outlet spigot Green and Yellow Earth Blue Interest of the environmentElectrical connection With the following codePermanent connection Building-in Preparation and assembly of the doorMounting the door Hardwood strip Ecological hints Environment concernsPackaging materials Old machinePage 132 963 770-01-302008 Subject to change without notice