Kenmore 110.6704, 110.6703 manual @ Sp el, If the dryer will not start, check the following

Page 17

3. Remove the 4 screws from the opposite side of the door.	6= Hang door	by placing	screw heads into top slotted	holes of
	hinges and	slide door	down. Align bottom screw holes in
	hinge and door. Install		two bottom screws. Tighten	all hinge
	screws.

I

I

4.Install the 2 hinges to the front panel of the dryer using

4 screws. Use the non-slotted side to attach the hinge to the front panel.

5.Install screws in the top hinge holes in the door. Do not tighten screws. Leave approximately W' (5 mm) of screw exposed.

A. Install these screws first.

7.Close door to engage door strike.

©@' Sp el_{!}

1.Check that all parts are now installed. If there is an extra part, go back through the steps to see which step was skipped.

2.Check that you have all of your tools.

3.Dispose of/recycle all packaging materials.

4.Check the dryer'sfinal location. Be sure the vent is not crushed or kinked.

5.Check that the dryer is level. See "Level Dryer."

6.For power supply cord installation, plug into an outlet. For direct wire installation, turn on power.

7.Remove any protective film or tape remaining on the dryer.

NOTE: Glass door models have a protective film on the window that should be removed.

8.Read "Dryer Use."

9.Wipe the dryer drum interior thoroughly with a damp cloth to remove any dust.

f0. Test dryer operation by selecting a Timed Dry heated cycle and starting the dryer. For this test, do not select the Air Only modifier.

If the dryer will not start, check the following:

•Controls are set in a running or "On" position.

•Start button has been pushed firmly.

•Dryer is plugged into an outlet and/or electrical supply is on.

•Household fuse is intact and tight, or circuit breaker has not tripped.

•Dryer door is closed.

11.When the dryer has been running for 5 minutes, open the dryer door and feel for heat. If you feel heat, cancel cycle and close the door.

If you do not feel heat, turn off the dryer and check the following:

•There may be 2 household fuses or circuit breakers for the dryer. Check that both fuses are intact and tight, or that both circuit breakers have not tripped. If there is still no heat, contact a qualified technician.

NOTE: You may notice an odor when the dryer is first heated. This odor is common when the heating element is first used. The odor will go away.

17

Image 17

Contents Oasis Table of Contents ONE Year Limited Warranty Kenmore Elite Appliance WarrantyProtection Agreements Disclaimer of Implied Warranties Limitation RemediesINSTRUCTiONS Dryer SafetyParts needed Parts suppliedDryer Dimensions 1403. H 2769 A6 cm Installation ClearancesMobile Home Additional Installation Requirements Mobile home installations requireIf your outlet looks like this If connecting by direct wireElectrical Connection Style 1 Power supply cord strain relief Power Supply Cord Direct WireWire connection Power supply cord Style 2 Direct wire strain reliefWire connection Direct Wire CG F Optional 3-wire connection If this is a new vent system Vent material If using an existing vent systemRigid metal vent Flexible metal ventFire Hazard Optional exhaust installationsSpecial provisions for mobile home installations Determine vent path Vent system chartRigid metal FlexibleReinstall the door If the dryer will not start, check the following @ Sp elTo use an Auto Dry Cycle Dryer USEExplosion Hazard To use a Timed Cycle To make changes during an Auto Dry CycleTo stop or pause your dryer at any time Drying tipsNormal Cool DownHeavy Duty Auto Dry Cycle Modifiers Auto Preset Cycle SettingsTimed Preset Cycle Settings Cycle Signal Damp Dry SignalChanging the Preset Dryness Level Settings Wrinkle Guard 30, 60, 90, 150 minutesItems for Rack Cycle Drying Setting Time MinutesTo use the dryer rack As needed cleaning To cleanTo clean dryer drum Dryer CareFor direct-wired dryers Moving care For power supply cord-connected dryersFrom Inside the Dryer Cabinet From the Exhaust VentNo heat TroubleshootingUnusualsounds Dryer displaying code messageIs the exhaust vent the correct length? Are fabric softener sheets blocking the grille?Is the exhaust vent diameter the correct size? Is the dryer located in a closet?Seguridad DE LA Secadora Instrucciones Contratos DE ProteccionUSO DE LA Secadora CuidadoContratos Maestros de Proteccibn Contratos DE ProteccionRevisi6n Anual de Mantenimiento Preventivo a solicitud Garanta Limitada DE UN AiioSu seguridad y la seguridad de los demas es muy importante Seguridad DE LA SecadoraPiezas necesarias Piezas suministradasUsted es responsable de Re u si tos e cldcosSi el contacto de pared luce come ste Si emplea un cable de suministro electricoSi el contacto de pared luce come este Si hace la conexibn con cableado directoCabledesuministroelctricoCabledirecto Conexibn de 4 hilos Cable de suministro elctrico Estilo 2 Protector de cables para cable directoCon Secci6n Conexibn de 4 hilos Cable directo CG F Page Si usa un sistema de ventilacibn existente Peligro de IncendioInstalaciones recomendadas de escape Ducto de escape de metal flexibleInstalaciones opcionales de escape Determinacibn de la via del ducto de escapeCuadro del sistema de ventilacibn Vuelva a instalar la puerta C6mo quitar el ensamblaje de la puertaCbmo invertir el tope Si la secadora no funciona, revise Io siguiente USO DE LA Secadora Para reanudar la marcha de la secadora Para hacer cambios durante un ciclo de secado automaticoPara usar un ciclo programado Sugerencias de secado Luces indicadoras Indicator LightsSugerencias de ciclos Htmedo DampDuty Modificadores del ciclo de secado automatico Ajustes prefijados de ciclos programadosSerial de ciclo Cycle Signal Serial de semi seco Damp Dry SignalCambio de ciclos despu6s de presionar puesta en marcha Cbmo cambiar los ajustes prefljados de nivel de sequedadEstante Para limpiar Cuidado DE LA SecadoraImportante Limpieza segun la necesidadEn el ducto de escape En el interior del gabinete de la secadoraPara cambiar la luz del tambor Cuidado para las vacacionesLa secadora muestra mensajes codificados Sin calorManchas en la carga o en el tambor Sears