Kenmore 110.6703, 110.6704 manual Reinstall the door

Page 16

Check the levelness of the dryer. Check levelness first side to side, then front to back.

If the dryer is not level, prop up the dryer using a wood block. Use a wrench to adjust the legs up or down and check again for levelness.

You can change your door swing from a right-side opening to a left-side opening, if desired.

1.Place a towel or soft cloth on top of the dryer or work space to protect the surface.

Remove the door assembly

1.Open the dryer door.

2.Remove the bottom screw from each of the 2 hinges that attach the dryer door to the front panel of the dryer.

3.Loosen the top screw from each of the 2 hinges in Step 2.

.A

.B

.A

"B

A. Loosen these screws.

B. Remove these screws.

4= Remove the dryer door and the hinges by lifting upward on the door. Lay the door on a flat, protected surface, with the inside of the door facing up. Remove remaining 2 loose screws from dryer front panel.

5= Remove the 4 plastic plugs located outside the dryer door opening.

It

---}P_ Io

6.Install 4 plastic plugs into screw holes in the dryer left when the hinges were removed in Step 4.

Reverse the strike

1.Remove the door strike from the dryer door opening.

2.Remove the cosmetic screw opposite the door strike.

A. Door strike

B. Cosmetic screw

3.Reinstall the door strike and cosmetic screw on the opposite side of the dryer door opening from where they were removed.

NOTE: Door strike and plugs must be on the same side of the dryer door opening.

Reinstall the door

1.Remove the 4 screws and 2 hinges from the dryer door.

2.Replace the 4 screws in the same holes.

16

Image 16

Contents Oasis Table of Contents Kenmore Elite Appliance Warranty ONE Year Limited WarrantyProtection Agreements Disclaimer of Implied Warranties Limitation RemediesDryer Safety INSTRUCTiONSParts supplied Parts neededInstallation Clearances Dryer Dimensions 1403. H 2769 A6 cmMobile Home Additional Installation Requirements Mobile home installations requireElectrical Connection If connecting by direct wireIf your outlet looks like this Power Supply Cord Direct Wire Style 1 Power supply cord strain reliefStyle 2 Direct wire strain relief Wire connection Power supply cordWire connection Direct Wire CG F Optional 3-wire connection If using an existing vent system If this is a new vent system Vent materialRigid metal vent Flexible metal ventSpecial provisions for mobile home installations Optional exhaust installationsFire Hazard Vent system chart Determine vent pathRigid metal FlexibleReinstall the door @ Sp el If the dryer will not start, check the followingExplosion Hazard Dryer USETo use an Auto Dry Cycle To make changes during an Auto Dry Cycle To use a Timed CycleTo stop or pause your dryer at any time Drying tipsHeavy Duty Cool DownNormal Timed Preset Cycle Settings Auto Preset Cycle SettingsAuto Dry Cycle Modifiers Damp Dry Signal Cycle SignalChanging the Preset Dryness Level Settings Wrinkle Guard 30, 60, 90, 150 minutesTo use the dryer rack Drying Setting Time MinutesItems for Rack Cycle To clean As needed cleaningTo clean dryer drum Dryer CareMoving care For power supply cord-connected dryers For direct-wired dryersFrom Inside the Dryer Cabinet From the Exhaust VentTroubleshooting No heatUnusualsounds Dryer displaying code messageAre fabric softener sheets blocking the grille? Is the exhaust vent the correct length?Is the exhaust vent diameter the correct size? Is the dryer located in a closet?Contratos DE Proteccion Seguridad DE LA Secadora InstruccionesUSO DE LA Secadora CuidadoContratos DE Proteccion Contratos Maestros de ProteccibnRevisi6n Anual de Mantenimiento Preventivo a solicitud Garanta Limitada DE UN AiioSeguridad DE LA Secadora Su seguridad y la seguridad de los demas es muy importantePiezas suministradas Piezas necesariasRe u si tos e cldcos Usted es responsable deSi emplea un cable de suministro electrico Si el contacto de pared luce come steSi el contacto de pared luce come este Si hace la conexibn con cableado directoCabledesuministroelctricoCabledirecto Con Secci6n Estilo 2 Protector de cables para cable directoConexibn de 4 hilos Cable de suministro elctrico Conexibn de 4 hilos Cable directo CG F Page Peligro de Incendio Si usa un sistema de ventilacibn existenteDucto de escape de metal flexible Instalaciones recomendadas de escapeDeterminacibn de la via del ducto de escape Instalaciones opcionales de escapeCuadro del sistema de ventilacibn Cbmo invertir el tope C6mo quitar el ensamblaje de la puertaVuelva a instalar la puerta Si la secadora no funciona, revise Io siguiente USO DE LA Secadora Para usar un ciclo programado Para hacer cambios durante un ciclo de secado automaticoPara reanudar la marcha de la secadora Luces indicadoras Indicator Lights Sugerencias de secadoSugerencias de ciclos Htmedo DampDuty Ajustes prefijados de ciclos programados Modificadores del ciclo de secado automaticoSerial de semi seco Damp Dry Signal Serial de ciclo Cycle SignalCambio de ciclos despu6s de presionar puesta en marcha Cbmo cambiar los ajustes prefljados de nivel de sequedadEstante Cuidado DE LA Secadora Para limpiarImportante Limpieza segun la necesidadEn el interior del gabinete de la secadora En el ducto de escapePara cambiar la luz del tambor Cuidado para las vacacionesSin calor La secadora muestra mensajes codificadosManchas en la carga o en el tambor Sears