ADC AD-410 service manual Table of Contents

Page 5

Table of Contents
AD-310 REFERENCE GUIDE
Tumbler Section	3
AD-310 REFERENCE GUIDE
Base Section	4
INTRODUCTION	5
AD-410 MACHINE OPERATION SUMMARY	5
AD-410 OPERATOR CONTROLS/INDICATORS	5
AD-410 MACHINE OPERATION TROUBLESHOOTING INFORMATION	8
SECTION I
SAFETY PRECAUTIONS	16
SECTION II
ROUTINE MAINTENANCE	18
A. Cleaning	18
B. Lubrication	20
C. Adjustments	21
SECTION III
SPECIFICATIONS and DIMENSIONS	22
A. Specifications (Gas and Steam Models)	22
B. Dimensions	23
SECTION IV
INSTALLATION REQUIREMENTS	25
A. Enclosure/Air Supply/Exhaust Requirements	25
B. Electrical and Gas Requirements	26
SECTION V
COMPONENT DESCRIPTION/REPLACEMENT	27
A. Heat Section	27
B. Troubleshooting The Direct Spark Ignition (DSI) System	31
C. Natural Gas and L.P. (Liquid Propane) Gas Conversion Instructions	43
D. Steam Coil System Operation	45
E. Sprinkler System Description	50
F. Tilting System Description	56
G. Air Jet Assembly	63
H. Blower (Squirrel Cage Fan) Motor Assembly	65
I. Filter and Regulator Assembly	72
J. Door Systems	73
K. Control and Electrical System	80
L. Tumbler (Basket) System	95

Image 5

Contents American Dryer Corporation Important Note to Purchaser Retain This Manual In a Safe Place For Future ReferenceFor Your Safety Page Table of Contents Section Troubleshooting AD-410 Reference Guide Base Section AD-410 Machine Operational Summary AD-410 Operator CONTROLS/INDICATORSControl Power On END of Cycle / Heater Fault Indicator / AIR JET AIR JET AD-410 Machine Operation Troubleshooting InformationLoad Tilted Unload TiltedDRY GAS Pressure If Both AIR Flow Switches are not Open AT this TimeImportant Information ONE 1 Burner will not Ignite During a Drying Cycle System Ladder DiagramONE 1 Burner will not Ignite AT the Beginning of a Cycle Lint Drawer / Guard Status Optional Sprinkler Control SignalsSolenoid Control Page What to do if YOU Smell GAS Explosion could ResultNational Electric Code ANSI/NFPA no -LATEST Edition StandardsLiquids CleaningSuggested Cleaning Schedule Monthly Lubrication Days After Installation and Every 6 Months Thereafter AdjustmentsGas Dimensions AD-410 with Inlet AIR Adapter Enclosure / AIR Supply / Exhaust Requirements Installation RequirementsElectrical Requirements and GAS Requirements Operational Service Check ProcedureDirect Spart Ignition DSI System COMPONENTS/FUNCTIONS Heat Section24 VAC Direct Spark Ignition DSI Module Repairable ADC Direct Spark Ignition DSI Operation Flow Chart Manometer Troubleshooting the Direct Spark Ignition DSI SystemMAN0677 Page If not, refer to the Second Visual Check on First Visual Check Second Visual Check Third Visual Check Are no Retries Leaks with a Flame Continuously Page Page Create a Potential Safety Hazard Page General Overview Steam Coil System OperationPage Page Page Page Sprinkler System Description Require any adjustment Page Page Supplies Before Servicing the Dryer MAN3169 Tilting System Description Page Tilting Pistons Page Page Page Page AIR JET Assembly Page Blower Squirrel Cage Fan Motor Assembly Leave enough movement for V-belt adjustment Page Important do not Overtighten V-BELTS Important do not Overtighten V-BELTS Page Page Filter and Regulator Assembly Door Systems Page Page Page Page Allow a full 72 hours for the silicone to cure Page Control and Electrical System Page Button does not Disable the High Voltage to the Dryer If the Opposite Side is not LEVEL, the Dryer will not Tilt ºC + Page Page Page Page Page Page MAN3405 Page Page Page Tumbler Basket System Important do not Over Tighten Turnbuckle Install new V-belts Tighten turnbuckle For Gear Reducer removal refer to Section d on page 99 Page Do not tighten 101 102 103 Troubleshooting Drive motor is not operating does not start Impellor fan motor is not operating does not start 107 108 Dryer operates but is taking too long to dry Excessive noise and vibration Dryer will not level from a tilt position Procedure for Functional Check Replacement Components 113 ADC450414 1- 05/27/99-25